Dell Inspiron 1410 Service Manual Download

Page: 1 / 35

Dell™ Inspiron™ 1410 Service Manual

Notes, Notices, and Cautions

Information in this document is subject to change without notice.

Reproduction of these materials in any manner whatsoever without the written permission of Dell Inc. is strictly forbidden.

Trademarks used in this text:

Dell

, the

DELL

logo,

and Inspiron

are trademarks of Dell Inc.;

Bluetooth

is a registered trademark owned by Bluetooth SIG, Inc. and is used by Dell

under license.

Microsoft

Windows, Windows Vista, and Windows Vista start button

are either trademarks or registered trademarks of Microsoft Corporation in the United States and/or

other countries.

Other trademarks and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Dell Inc. disclaims any
proprietary interest in trademarks and trade names other than its own.

Model PP38L

August 2008 Rev. A00

Before You Begin

Module Cover

Memory Module

Mini-Cards

Center Control Cover

Keyboard

Display

Palm Rest

System Fan

Processor Heat Sink

Processor

Hard Drive

Coin-Cell Battery

Optical Drive

Speaker

Internal Card With Bluetooth

Wireless Technology

System Board

Battery Latch Assembly

Flashing the BIOS

NOTE:

A NOTE indicates important information that helps you make better use of your computer.

NOTICE:

A NOTICE indicates either potential damage to hardware or loss of data and tells you how to avoid the problem.

CAUTION:

A CAUTION indicates a potential for property damage, personal injury, or death.

Summary of Contents for Inspiron 1410




































Search results

Summary of Contents for Inspiron 1410

Reviews:

Related manuals for Inspiron 1410

Brands by name

Popular brands

Dell Inspiron 1410, Service Manual

Search results

Summary of Contents for Inspiron 1410

Reviews:

Related manuals for Inspiron 1410

Brands by name

Popular brands