B1. AC Power Socket
B2. Serial Port (Optional)
B3. DisplayPort
B4. HDMI Port
B5. USB 3.0 Port
B6. eSATA Port
B7. LAN Port
B8. Clear CMOS Button
B9. Front Speaker Out (L/R) Port
B10. Line-In Port
B11. Side Speaker Out (L/R) Port
B12. Real Speaker Out (L/R) Port
B13. Center/Subwoofer
Speaker Out Port
B14. Wireless LAN Perforation
(Optional)
11. Fasten the Smart Fan to the chassis with the four thumbscrews.
A. Begin Installation
1. Unscrew 3 thumbscrews of the chassis cover.
2. Slide the cover backwards and upwards.
3. Unfasten the rack mount screws and remove the rack.
B. CPU and ICE Installation
For safety reasons, please ensure that the power cord is
disconnected before opening the case.
1. Unfasten the ICE fan thumbscrews on the back of the chassis.
2. Unfasten the four ICE module attachment screws and unplug the fan
connector.
3. Remove the ICE module from the chassis and put it aside.
1. Unlock the DIMM latch.
2. Align the memory module's cutout with the DIMM slot notch.
Slide the memory module into the DIMM slot.
C. Memory Module Installation
3. Check that the latches are closed, and the memory module is firmly installed.
E. Installation of Expansion Cards
1. Unfasten the expansion slot bracket screws.
Remove the back panel bracket and put it aside.
F. Installation of Expansion Cards
2. Install the PCIe x4 / PCIe x16 card into the PCIe x4 / PCIe x16 slots.
3. Secure the bracket.
G. Complete
Please press the "Del" key while booting to enter BIOS. Here,
please load the optimised BIOS settings.
The maximum size acceptable for display cards is
267mm x 120mm x 34.6mm.
1. Replace the cover and refasten the thumbscrews.
2. Complete.
Make sure that the motherboard supports the memory.
It is recommended that memory of the same capacity, brand,
speed, and chips are used.
(Go to Shuttle's website for the latest memory support list.)
Memory modules have a foolproof design. A memory module can
be installed in only one direction. If you are unable to insert the
memory, switch the direction.
Guidelines for Memory Configuration
Before installing DIMMs, read and follow these guidelines for memory
configuration.
Installing a memory module
DDR4 and DDR3/DDR2 DIMMs are not compatible to each other or other
DDR DIMMs.
Be sure to install DDR4 DIMMs on this motherboard. Follow the steps
below to correctly install your memory modules in the memory sockets.
Repeat the above steps to install additional memory modules,
if required.
A DDR4 memory module has a cutout, so it only fits in one direction.
4. First unlock and raise the socket lever.
This 1151-pin socket is easily damaged and pins bend quickly.Always
use extreme care when installing a CPU and limit the number of times
that you remove or change the CPU. Before installing the CPU, make
sure to turn off the computer and unplug the power cord from the
power outlet to prevent damage to the CPU.
Follow the steps below to correctly install the CPU into the
motherboard CPU socket.
Please be aware of the CPU orientation, DO NOT force the CPU into
the socket to avoid bending of pins and damage of CPU!
6. Please orientate the CPU correctly and align the CPU notches with the
socket alignment keys. Make sure the CPU sits perfectly horizontal, then
push it gently into the socket.
DO NOT touch socket contacts. To protect the CPU socket, always
replace the protective socket cover when the CPU is not installed.
Socket
1151
CPU
Triangle Pin1
Marking
on the CPU
L
The product's colour and specifications may vary from the actually shipping product.
5. Connect the Serial ATA and power cables to the HDD.
3. Connect the Serial ATA Cable to the motherboard.
4. Place the rack in the chassis and refasten the rack.
1. Loosen the purse lock and separate the Serial ATA and power cables.
7. Close the metal load plate, lower the CPU socket lever and lock in place.
8. Spread thermal paste evenly on the CPU surface.
5. Tear off the protective membrane from the metal load plate. Lift the
metal load plate on the CPU socket.
Dual-Channel mode Population Rule
In Dual-Channel mode, the memory modules can transmit and receive
data with two data bus lines simultaneously. Enabling Dual-Channel
mode can enhance the system performance. The following illustrations
explain the population rules for Dual-Channel mode.
DIMM1 (Black), Installed
DIMM2 (Blue), Installed
DIMM3 (Black), Installed
DIMM4 (Blue), Installed
A
B
9. Screw the ICE module to the mainboard. Note to press down on the
opposite diagonal corner while tightening each screw.
10. Connect the fan connector.
J3
Fan Connectors (FN1,FN2)
J2
USB Header (USB1,USB2)
1=5V_USB
2=5V_USB
3=USB A-
4=USB B-
5=USB A+
6=USB B+
7=GND
8=GND
9=NULL
10=GND
J1
Front Audio Header (JP2)
1=MIC_L
2=GND
3=MIC_R
4=Front_Detect
5=LINE_R
6=Mic_detect
7=sense
8=NULL
9=LINE_L
10=Line_Detect
J4
USB 3.0 Header (JP5)
1=5VCC
2=A_RX_N
3=A_RX_P
4=Ground
5=A_TX_N
6=A_TX_P
7=Ground
8=A_Data_N
9=A_Data_P
10=OC
11=B_Data_P
12=B_Data_N
13=Ground
14=B_TX_P
15=B_TX_N
16=Ground
17=B_RX_P
18=B_RX_N
19=5VCC
20=NULL
DIMM1 (Black), Empty
DIMM2 (Blue), Installed
DIMM3 (Black), Empty
DIMM4 (Blue), Installed
Motherboard Illustration
Back Panel
SZ170R8 Quick Guide【 English 】
Front Panel
Jumper Settings
Please do not apply excess amount of thermal paste.
2. Install the Mini PCIE card / M.2 SSD into the Mini PCIE slot / M.2 slot and
secure with screw.
D. Component Installation
53R-SZ1703-H501
Safety Information
Read the following precautions before setting up a Shuttle XPC.
CAUTION
Incorrectly replacing the battery may damage this computer. Replace only with the same
or equivalent as recommended by Shuttle. Disposal of used batteries according to the
manufacturer's instructions.
Laser compliance statement
The optical disc drive in this PC is a laser product.
The drive's classification label is located on the drive.
CLASS 1 LASER PRODUCT
CAUTION:
INVISIBLE LASER RADIATION WHEN OPEN. AVOID EXPOSURE TO BEAM.
PCIe x16 slot
PCIe x4 slot
Serial ATA Cable
Serial ATA Power Cable
J7
Power Connector (JP4)
1=+HD_LED
2=PWR_LED
3=-HD_LED
4=GND
5=RST_SW
6=PWR_SW
7=GND
8=GND
9=NA
10=NULL
9 7 5 3 1
10 8 6 4 2
J6
COM Header (COM1)
1=DCD
2=RXD
3=TXD
4=DTR
5=Ground
6=DSR
7=RTS
8=CTS
9=NA
10=NULL
9 7 5 3 1
10 8 6 4 2
1 3 5 7 9
2 4 6 8 10
1
3
5
7
9
2
4
6
8
10
1=Ground
2=+12V
3=SPEED_SENSE
4=PWM_CTRL
Fan Connector
1
2
3
4
4
3
2
1
11 12 13 14 15 16 17 18 19 20
10 9 8 7 6 5 4 3 2 1
Thermal Paste
application area
Cutout
Latch
Latch
Notch
DDR4 288 pin 1.2V
67*2=134 pin
77*2=154 pin
2
1
3
Fan Connector
J5
LPC Header (LPC1)
10
9
8
7
6
5
4
3
2
1
20
19
18
17
16
15
14
13
12
11
1=+12V
2=5V
3=5VSB
4=SERIRQ
5=CLK_48M
6=CLK_33M
7=SIO_RST
8=LFRAME
9=LAD3
10=LAD2
11=-12V
12=3VSB
13=NA
14=LDRQ0
15=SIO_PME
16=LAD1
17=LAD0
18=+3.3V
19=GND
20=NULL
Metal load plate
Tear off the protective
membrane.
Mini PCIE slot
1. As shown, unfasten the screw first.
M.2 slot
J2
J3
J4
J7
J6
4x 288 pins DDR4 DIMM Slot
Side Speaker Out /
Real Speaker Out / Center /
Subwoofer Speaker Out Port
Front Speaker Out / Line-In Port
2x USB 3.0 & 1x LAN Port
ATX Power Connector-PWR1
ATX Power Connector-ATX1
Front Audio Header-JP2
USB Header-USB1
Power Connector-JP4
LGA 1151
FAN Connector-FAN1
2x DisplayPort
One PCIe x4 Slot
One PCIe x16 Slot
2x USB 3.0 & 1x eSATA Port
Clear CMOS Button
LPC Header-LPC1
USB 3.0 Header-JP5
2x USB 3.0 & 1x HDMI Port
COM Header-COM1
Intel
®
Z170 Chipset
USB Header-USB2
Mini PCIe Slot
M.2 Slot
J5
J2
J1
J3
FAN Connector-FAN2
SATA 3.0 6Gb/s Connector
-SATA1,SATA2,SATA3,SATA4
B1
B2
B9
B12
B13
B11
B14
B5
B8
B7
B3
B4
B6
B10
F1. Power On Button
F2. Power LED
F3. HDD LED
F4. USB 3.0 Port
F5. Mic In
F6. Headphones
F1
F2
F3
F6
F5
F4
1
2
SATA 3.0 Connectors
Serial ATA HDD
1st
2nd
3rd
4th
SATA 3.0 Connectors
2. Place the HDD in the rack and
secure with screws from the side.
6. Repeat these steps to install up to four 3.5" HDDs, if desired.
VGA Card PCB
Chassis
Cover
5mm
34.6mm
PCIe x16 / PCIe x4 slots
The maximum height
for memory module
is 42mm.
42mm
62R-SZ1701-5201 SZ170R8
English.Spanish.Korean.
Traditional Chinese.Japanese.
French. German Quick Guide
