Garland MWE3S Service Manual Download Page 43

Page: 43 / 72

PART #4526396 (03/30/10)

GARLAND CLAMSHELL GRILLS WITH PRODUCT RECOGNITION

SERVICE MANUAL

Page 43

REED SWITCH OPERATION

(continued)

FRONT

REED

REAR

REED

LOWER��

LIMIT

UPPER�

LIMIT

CLOSED

OPEN

Platen in the Up Position – Switches are in NORMAL state.

OPEN

Platen movement command has been initiated.

Upper Limit switch as OPENED.

OPEN

CLOSED

OPEN

Platen has moved to the DOWN position.

Lower Limit switch has CLOSED.

OPEN

Platen has raised up to PREHEAT GAP SETTING of .450.

Lower Limit Switch OPENS.

AUTO�CALIBRATION�BEGINS�AFTER�GRILL�REACHES�TEMPERATURE�AND�COUNTDOWN�TIMER�EXPIRES

OPEN

CLOSED

OPEN

Auto calibration begins. Lower Limit Switch CLOSES

OPEN

CLOSED

OPEN

Platen continues to move down. Rear Reed Switch CLOSES.

OPEN

CLOSED

Platen continues to move down. Front Reed Switch CLOSES.

OPEN

CLOSED

OPEN

Linear Actuator reverses polarity. Platen Raises.

Front Reed Switch OPENS.

OPEN

CLOSED

OPEN

Platen continues to rise. Rear Reed Switch OPENS.

OPEN

Platen continues to ruse. Lower limit switch opens.

CLOSED

OPEN

Platen continues to ruse. Upper Limit switch OPENS.

Movement stops.

Summary of Contents for MWE3S









































































Search results

Summary of Contents for MWE3S

Reviews:

Related manuals for MWE3S

Brands by name

Popular brands

Garland MWE3S, Service Manual

Search results

Summary of Contents for MWE3S

Reviews:

Related manuals for MWE3S

Brands by name

Popular brands