Garland MWE3S Service Manual Download Page 19

Page: 19 / 72

PART #4526396 (03/30/10)

GARLAND CLAMSHELL GRILLS WITH PRODUCT RECOGNITION

SERVICE MANUAL

Page 19

INSTALLATION OF RELEASE MATERIAL

INSTALLATION OF VAPOR SHIELD

1. Slide release material rod through hemmed end of the

release material sheet.

2. Hook release

material rod on

brackets located

at the rear of the

upper platen.

3. Holding the

bottom of the

release material

sheet in place,

gently pull the

sheet toward the front of the platen.

NOTE: Make sure release material fits smoothly over upper

platen.

4. Place one (1)

locking clip over

release material

sheet in front

and press into

place over release

material bar.

5. Gently pull the

release material

sheet flap over

the left side of the

platen and secure in place with two (2) locking clips.

HEMMED

LOOP

MATERIAL

ROD

RELEASE

MATERIAL

“Teflon Sheet” available from your DC

Saint Gobain: DC WRIN #

02180-003

Taconic: DC WRIN #

02180-000

MATERIAL ROD

HOLDER

MATERIAL

ROD

RELEASE

MATERIAL

UPPER

PLATEN

(SIDE VIEW)

6. Repeat step 5

with the right

side.

NOTE: Failure to

install the correct

number of clips on

the upper platen

will cause the

release material to

be loose, and wear

quickly. Ensure the

correct placement

of ALL clips to

prevent premature

wear and/or poor

product quality.

5. Check

alignment and

rightness of

release material

against upper

platen.

RELEASE

MATERIAL

FLAPS

RELEASE

MATERIAL

FLAPS

RELEASE

MATERIAL

CLIPS

TEFLON

FRONT

BAR

VAPOR SHIELD

UP & OVER

TEFLON

FRONT BAR

Summary of Contents for MWE3S









































































Search results

Summary of Contents for MWE3S

Reviews:

Related manuals for MWE3S

Brands by name

Popular brands

Garland MWE3S, Service Manual

Search results

Summary of Contents for MWE3S

Reviews:

Related manuals for MWE3S

Brands by name

Popular brands