![background image](http://html1.mh-extra.com/html/garland/mule-961-qg/mule-961-qg_instruction-manual_3656798047.webp)
English
46/184
English
47/184
clutch is not correctly regulated take your machine for
service.
6.4.2. STARTING THE ENGINE
Start the engine carefully, in accordance with the
instructions, and feet away from the milling cutters.
6.4.2.1. COLD-STARTING THE ENGINE
Place the machine on a flat surface and stable to start
it.
1. Place the ON/OFF switch in the “ON” position.
2. Place the handle switch in the position “I”.
3. Place the fuel tap in the open position.
4. Place the air lever in the Closed position .
5. Place the accelerator lever in the maximum
position.
.
6. Place yourself behind the machine, as shown in the
figure, and pull the Starter rope until the engine
starts.
7. If the machine starts and does not stop, slowly
begin moving the air lever toward the Open air
position (normal working position).
8. Adjust the appropriate number of revolutions with
the throttle lever.
9. Allow the engine to warm up for a few minutes
before starting to use the machine.
6.4.2.2. STARTING WITH A HOT ENGINE
Place the machine on a flat surface and stable to start
it.
1. Place the ON/OFF switch in the “ON” position.
2. Place the handle switch in startup position (“I”).
3. Place the fuel faucet in the Open position.
4. Place the air lever in the Open position
(Normal working position)
5. Place yourself behind the machine and pull the
Starter rope until the engine starts.
6. Adjust the appropriate number of revolutions with
the throttle lever.
Normal working
position
Summary of Contents for MULE 961 QG
