Garland CFA Garland Grill 2.0 Installation, Operation And Maintenance Manual Download Page 4 | Manualshive

Page: 4 / 56

background image

Notice

This appliance is not approved or authorized for home
or residential use, but is intended for commercial
applications only. The manufacturer and/or authorized
representative will not provide service, warranty,
maintenance or support of any kind other than in
commercial applications.

Notice

Routine adjustments and maintenance procedures
outlined in this manual are not covered by the warranty.

LOCATION

n

Warning

To avoid instability the installation area must be capable
of supporting the combined weight of the equipment
and product. Additionally the equipment must be
level per instructions given in this manual, section 2
Installation.

n

Warning

No structural material on the appliance should be altered
or removed to accommodate placement of the appliance
under a hood.

,

Caution

This equipment must be operated under an approved
hood system in accordance with local regulations in
force. This unit is intended for indoor use only.

CODE

n

Warning

Authorized Service Representatives are obligated to
follow industry standard safety procedures, including,
but not limited to, local/national regulations for

disconnection / lock out / tag out procedures for all
utilities including electric, gas, water and steam.

Important

Additional Safety Notices are stated in the relevant
sections throughout the manual.

Safety Notices (continued)

«
...
2
3
4
5
6
...
»

Summary of Contents for CFA Garland Grill 2.0

























































Reviews:

No comments

Related manuals for CFA Garland Grill 2.0

Brand: Skil Pages: 32

Brand: Hilti Pages: 15

Brand: Swann Pages: 10

Brand: EL TORO Pages: 24

Brand: Master Chef Pages: 24

MegaMixer AMX110

Brand: Intex Pages: 12

OPTIGRILL GC705D16

Brand: TEFAL Pages: 112

Professional VEOS100T

Brand: Viking Pages: 6

Brand: RIVVAL Pages: 16

Brand: Ryobi Pages: 24

Brand: Klarstein Pages: 36

Brand: Klarstein Pages: 36

Red Line ID 500

Brand: Stark Pages: 25

Brand: Monument Grills Pages: 23

Brand: Rotabroach Pages: 20

ALFRESCO BG2294B-G

Brand: Barbeques Galore Pages: 26

Brand: Barbecook Pages: 102

Brand: Barbecook Pages: 56

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands