manualshive.com logo in svg

Garland CFA Garland Grill 2.0, Installation, Operation And Maintenance Manual, Page: 17 / 56

Share
Download
Garland CFA Garland Grill 2.0 Installation, Operation And Maintenance Manual Download Page 17

Document Number:   GAR_IOM_CFABROILER_4603091   rev 00   (08/21/2017) 

17

Section 2 

Installation

4.  Adjust the caster assembly by turning the caster 

counterclockwise to increase the height or clockwise 
to decrease the height.

5.  The RED MARK on the threaded stem indicates the 

maximum adjustment. These RED MARKS MUST NOT 
BE VISIBLE.

n

Warning

Adjusting the height above the red mark could 

cause the caster to fail and the unit to tip over.

FRONT CASTER WITH BRAKE

REAR CASTER WITHOUT BRAKE

Red Mark in Shaft

Should

NOT be Visible

Caster Jam Nuts

6.  To secure the caster assembly, tighten the caster jam 

nut against the chassis. 

REMOVING STAINLESS STEEL PLASTIC FILM COVER

All plastic protective film must be removed before turning 
on the appliance. 

The film covers both internal and external components (e.g. 
side panels, grease shield).

1.  Using a plastic scraper, wedge the film away from the 

stainless steel.

2.  Grasp and pull the film very gently away from the 

stainless steel.

PEEL OFF PL

ASTIC FILM

REMOVING THE “DESI PAK” BAGS (IF REQUIRED)

• 

Desi Pak are used to protect the electronic components 
by controlling humidity levels within the equipment.

• 

Desi Pak bags are only intended to be left inside the 
equipment during shipping and storage. .

• 

Keep these bags in the equipment while in storage or 
not in operation.

To remove the Desi Pak:

1.  Turn the Green Power 

Main Switch OFF

. 

(Green light is off.)

2.  Remove the two Phillip screws located on each side 

of the front panel below the user interface. Store the 
screws in a save place.

3.  Gently move the panel up slightly to dislodge from 

the hooks on each side. 

4.  Move the panel slowly away from the front. Watch 

and do not break the wires and connectors. 

5.  Remove the bags.

6.  Reinstall cover and tighten the screws.

Summary of Contents for CFA Garland Grill 2.0

























































Reviews:

No comments