Gardsman CTC-1052 User Manual Download Page 40

37 

5.5. CTC-1052 SMS Remote Programming Command Table 

 

If the SMS Keyword is set as 

PROG

, and Access Code is set as 

1111

 (factory default).

 

CORRESPON-

DING DTMF 

CHARACTER 

COMMANDS 

ITEM 

COMMAND 

EXAMPLE & USAGE 

DEFAULT

--- 

SMS 

Keyword 

(Installer) 

KEYWD 

PROG 1111 KEYWD:IPOG 
To set/change the SMS keyword for installer (4-character) 

PROG 

01# 

Telephone 

number 1 

TELN1 

PROG 1111 TELN1:0227940559
To set/change Telephone number 1 
(Max. 20 digits, Null=to clear Telephone number 1) 

No number

02# 

Telephone 

number 2 

TELN2 

PROG 1111 TELN2:0227940559
To set/change Telephone number 2 
(Max. 20 digits, Null=to clear Telephone number 2) 

No number

03# 

Telephone 

number 3 

TELN3 

PROG 1111 TELN3:0227940559
To set/change Telephone number 3 
(Max. 20 digits, Null= to clear Telephone number 3) 

No number

04# 

Telephone 

number 4 

TELN4 

PROG 1111 TELN4:0227940559
To set/change Telephone number 4 
(Max. 20 digits, Null=to clear Telephone number 4) 

No number

05# 

Telephone 

number for 

alarm report 

ALMRP 

PROG 1111 ALMRP:1234
To select the number for alarm report 
1=Telephone 1 , 2=Telephone 2 , 3=Telephone 3 
4=Telephone 4 , 5=GPRS1 , 6=GPRS2 

1,2,3,4,5,6

06# 

Telephone 

number for 

status report 

STARP 

PROG 1111 STARP:1234
To select then number for status report 
1=Telephone 1 , 2=Telephone 2 , 3=Telephone 3 
4=Telephone 4 , 5=GPRS1 , 6=GPRS2 

1,2,3,4,5,6

10# 

Global 

account 

number 

ACNTG 

PROG 1111 ACNTG:1234, To set/change the same 4- 6- 8-
digit account number for all 4 telephone numbers (Null=to 
clear 4 Telephone numbers) 

No 

account 

number

11# 

Account 

number 1 

ACNT1 

PROG 1111 ACNT1:1234, To set/change the 4- 6- 8-digit 
account number for Telephone number 1(Null=to clear 
account number for Telephone number 1) 

No 

account 

number

12# 

Account 

number 2 

ACNT2 

PROG 1111 ACNT2:1234, To set/change the 4- 6- 8-digit 
account number for Telephone number 2 (Null=to clear 
account number for Telephone number 2) 

No 

account 

number

13# 

Account 

number 3 

ACNT3 

PROG 1111 ACNT3:1234, To set/change the 4- 6- 8-digit 
account number for Telephone number 3 
(Null=to clear account number for Telephone number 3) 

No 

account 

number

14# 

Account 

number 4 

ACNT4 

PROG 1111 ACNT4:1234, To set/change t the 4- 6- 8-digit 
account number for Telephone number 4 (Null=to clear 
account number for Telephone number 4) 

No 

account 

number

20# 

Reporting 

method for 

all 4 

Telephone 

numbers 

FMATG 

PROG 1111 FMATG:0 
To set the reporting methods for all 4 Telephone numbers 
0=Contact ID, 1=Scancom, 2=Tunstall, 3=Speech, 
4=SMS CID 

0 = 

Contact ID

21# 

Reporting 

method for 

Telephone 

number 1 

FMAT1 

PROG 1111 FMAT1:0
To set the reporting method for Telephone number 1 
0=Contact ID, 1=Scancom, 2=Tunstall, 3=Speech, 
4=SMS CID 

0 = 

Contact ID

22# 

Reporting 

method for 

Telephone 

number 2 

FMAT2 

PROG 1111 FMAT2:0
To set the reporting method for Telephone number 2 
0=Contact ID, 1=Scancom, 2=Tunstall, 3=Speech 
4=SMS CID 

0 = 

Contact ID

23# 

Reporting 

method for 

Telephone 

number 3 

FMAT3 

PROG 1111 FMAT3:0
To set the reporting method for Telephone number 3 
0=Contact ID, 1=Scancom, 2=Tunstall, 3=Speech 
4=SMS CID 

0 = 

Contact ID

24# 

Reporting 

method for 

Telephone 

number 4 

FMAT4 

PROG 1111 FMAT4:0
To set the reporting method for Telephone number 4 
0=Contact ID, 1=Scancom, 2=Tunstall, 3=Speech 
4=SMS CID 

0 = 

Contact ID

Summary of Contents for CTC-1052















































Reviews: