Gardsman CTC-1052 User Manual Download Page 13

10 

Command 32  

Audible Fault Alert  

 

CTC-1052  can  be  programmed  to  emit 
Fault  Alert  Beeps 

every  30  seconds

  from 

AC Failure. 

Function Selection 

Result 

(0) 

OFF 

(No Warning Beep) 

(1) 

ON 

(With Warning Beep)

 

Factory Default

 

is

 

set as (

0

), 

OFF

.  

 

Command 33  

Help Arrived Signaling  

This function is available for Digital 
reporting, SMS reporting and GPRS 
reporting methods.  

 

It  is  used  for  the  Monitoring  Center 
personnel to confirm if the help has arrived 
for the user or not. 

 

This  function  will  be  activated  after 
successfully  reported  from  the  following 
situations:  

  Pressing  the 

Red  Help  Button

  on 

CTC-1052. 

  Pressing  the 

Active  button

  on  WTR, 

PB or Fall Sensor is pressed. 

  A fall detection. 

 

If Help Arrived Signaling is set to 

ON

, once 

the Alarm Reporting is completed, the 

Red 

Help  Button

 will start to flash as the panel 

enters Help Arrived Mode. 

 

If  Help  Arrived  Signaling  is  set  to 

OFF

CTC-1052  will  return  to  idle  mode  when 
Alarm Reporting is completed. 

Function Selection

Result 

(0) 

OFF

  

(Disable) 

(1) 

ON

  

 

(Enable) 

 

Factory Default is set as (

0

), 

OFF

.  

<NOTE> 

 

If  the 

Green  Reset  Button

  is  not 

pressed  within  the  period  set  by 
Command  67  (Help  Arrived  Timer), 
CTC-1052 will send the alarm report to 
summon  help  again  and  inform  the 
Monitoring  Center  that  no  help  has 
arrived within the period set by the Help 
Arrived Timer.  

 

Command  33  (Help  Arrived  Signaling) 
has  to  be  set  as 

ON

  for  Command  67 

(Help Arrived Timer) to be activated.  

 

If help has not arrived after sending the 
alarm report for 4 times, CTC-1052 will 
dial  the  telephone  number  set  by 
Command 

75

  and  open  two-way 

communication  when  the  call  is 
answered. 

 

 

Command 34  

Emergency Button Enable 

 

The 

Red  Help  Button

  can  be  enabled  or 

disabled  to  send  an  Emergency  alarm 
report:  

Function Selection 

Result 

(0) 

OFF 

(Disable) 

(1) 

ON 

(Enable) 

 

Factory Default

 

is

 

set as 

(1), ON

.  

 

OFF

:  Pressing  the 

Red  Help  Button

  is 

unable to send an emergency alarm.

 

 

ON

:  Pressing  the 

Red  Help  Button

  will 

activate  the  panel  send  an  emergency 
alarm.

 

 
 
 
 
 
 

Summary of Contents for CTC-1052















































Reviews: