background image

 

Form No. BT-28

 

 

Copyright © 2015 Gardner Denver, Inc

 

Standard Warranty  

Oil-Lubricated Rotary Screw / Rotary Vane Compressor Packages  
APEX, APEX VS, Electra Screw, Integra, Electra Saver II, Electra Saver, L, LRS, VS, VST, V, HV, HV 
RS, and HR Series   

 

STANDARD WARRANTY    

Gardner  Denver  (the 

“Company”)  warrants  to  each  original  retail  purchaser  (“Purchaser”)  of  its  new 

products from the Company or its authorized distributor that such products are, at the time of delivery to 
the Purchaser, free of defects in material and workmanship. 

This Standard Warranty statement applies 

to compressors shipped after April 1

st

, 2015. 

STANDARD WARRANTY PERIOD 

The  Company

’s  obligation  under  this  warranty  is  limited  to  repairing  or,  at  its  option,  replacing,  during 

normal  business  hours  at  an  authorized  service facility  of the  Company,  any  part  which in  its  judgment 
proved not to be as warranted within the applicable warranty period as follows.

 Regular maintenance in 

accordance with the service manual is required. Use of genuine Gardner Denver OEM parts and 
lubricants  are  highly  recommended.  If  a  component  failure  is  deemed  a  result  of  using  non-
genuine Gardner Denver parts and lubricants, warranty will not be allowed.  

 
 

  

 

 

 

 

 

 

 

 

 

 

 

 

 

 

NO WARRANTY IS MADE WITH RESPECT TO:  
1.  ANY PRODUCT WHICH HAS BEEN REPAIRED OR ALTERED IN SUCH A WAY, IN THE COMPANY’S 

JUDGMENT, AS TO AFFECT THE PRODUCT ADVERSELY 

2.  ANY PRODUCT WHICH HAS, IN THE COMPANY’S JUDGMENT BEEN SUBJECT TO NEGLIGENCE, 

ACCIDENT, IMPROPER STORAGE, OR IMPROPER INSTALLATION OR APPLICATION 

3.  ANY PRODUCT WHICH HAS NOT BEEN OPERATED OR MAINTAINED IN ACCORDANCE WITH THE 

RECOMMENDATIONS OF THE COMPANY 

4.  ANY RECONDITIONED OR PRIOR OWNED PRODUCT 
 

STANDARD WARRANTY DISCLAIMER 

 

THE  FOREGOING  WARRANTY  IS  EXCLUSIVE  AND  IT  IS  EXPRESSLY  AGREED  THAT,  EXCEPT  AS  TO  TITLE,  THE  COMPANY  MAKES  NO 
OTHER WARRANTIES  AND  HEREBY  EXPRESSLY  DISCLAIMS  ALL  OTHER WARRANTIES,  INCLUDING WITHOUT  LIMITATION,  EXPRESSED, 
IMPLIED  OR  STATUTORY WARRANTIES,  INCLUDING  ANY  IMPLIED  WARRANTY  OF  MERCHANTABILITY  OR  FITNESS  FOR  A  PARTICULAR 
USE.  THE  REMEDY  PROVIDED  UNDER  THIS  WARRANTY  SHALL  BE  THE  SOLE,  EXCLUSIVE  AND  ONLY  REMEDY  AVAILABLE  TO 
PURCHASER  AND  IN  NO  CASE  SHALL  THE  COMPANY  BE  SUBJECT  TO  ANY  OTHER  OBLIGATIONS  OR  LIABILITIES.  UNDER  NO 
CIRCUMSTANCES SHALL THE COMPANY BE  LIABLE FOR SPECIAL,  INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES, EXPENSES, 
LOSSES  OR  DELAYS  HOWSOEVER  CAUSED.  NO  STATEMENT,  REPRESENTATION,  AGREEMENT,  OR  UNDERSTANDING,  ORAL  OR 
WRITTEN,  MADE  BY  ANY  AGENT,  DISTRIBUTOR,  REPRESENTATIVE,  OR  EMPLOYEE  OF  THE  COMPANY  WHICH  IS  NOT  CONTAINED  IN 
THIS WARRANTY WILL BE BINDING UPON THE COMPANY UNLESS MADE IN W RITING AND EXECUTED BY AN OFFICER OF THE COMPANY. 
THIS  WARRANTY  SHALL  NOT  BE  EFFECTIVE  AS  TO  ANY  CLAIM  WHICH  IS  NOT  PRESENTED  WITHIN  30  DAYS  AFTER  THE  DATE  UPON 
WHICH  THE  PRODUCT  IS  CLAIMED  NOT  TO  HAVE  BEEN  AS  WARRANTED.  ANY  ACTION  FOR  BREACH  OF  THIS  WARRANTY  MUST  BE 
COMMENCED  WITHIN  ONE  YEAR  AFTER  THE  DATE  UPON  WHICH  THE  CAUSE  OF  ACTION  OCCURRED.  ANY  ADJUSTMENT  MADE 
PURSUANT TO THIS WARRANTY  SHALL  NOT  BE  CONSTRUED  AS  AN  ADMISSION  BY  THE  COMPANY  THAT  ANY  PRODUCT WAS  NOT  AS 
WARRANTED. WARRANTY IS NOT TRANSFERRABLE 

 

COMPONENT 

STANDARD WARRANTY COVERAGE 

DETAILS 

Package 

12 months

 from startup or 

15 months

 from date of 

shipment to first purchaser, whichever occurs first

 

All components within the package, excluding normal wear items 

Airend 

24 months

 from startup or 

27 months

 from date of 

shipment to first purchaser, whichever occurs first

 

Normal wearing items, such as shaft seals and inlet valve components, 
along with the servicing of these items is not covered under the warranty 
unless deemed as material or workmanship defects. Any disassembly or 
partial disassembly of the airend, or failure to return the 

“unopened” airend 

per Company instructions, will be cause for denial of warranty 

Electric Motors 

12 months

 from startup or 

15 months

 from date of 

shipment to first purchaser, whichever occurs first

 

Includes both drive motor and cooling fan motor. For nonstandard motors, 
the original manufacturer

’s warranty will take precedence.  

Major Package 

Components 

24 months

 from startup or 

27 months

 from date of 

shipment to first purchaser, whichever occurs first

 

Includes package controller, variable frequency drive if applicable, air/oil 
reservoir, air/oil cooler, and precision mixing valve (VS Series)  

Labor 

Package / Electric Motors: 12 months 

from 

startup

 

or

 15 months 

from date of shipment to first 

purchaser,

 

whichever occurs first

 

 
Airend / Major Package Components: 24 months

 

from startup or 

27 months

 from date of shipment to 

first purchaser, whichever occurs first

  

 

 

Service will be provided by Company representative or authorized service 
personnel, for repair or replacement of any product or part which in the 
Company

’s sole judgment is proved not to be as warranted. Labor shall be 

limited to the amount specified in the Company

’s labor rate schedule. All 

costs of transportation of product, parts, and repaired or replacement parts 
claimed not to be as warranted to and from such service facilities shall be 
borne by the Purchaser. The Company may require the return of any part 
claimed not to be as warranted to one of its facilities as designated by 
Company, transportation prepaid by Purchaser, to establish a claim under 
this warranty. Replacement parts provided under the terms of the warranty 
are warranted for the remainder of the Warranty Period.  

 

Summary of Contents for AirSmart G2









































































Reviews: