background image

Service Manual 

 

 

43/46 

Issue 3.1  

Ref. NR-00019-ENG 

http://www.gamapur.com/

 

 

Inlet supply filters 

The filter bodies have a filter screen that prevents solid particles from entering the unit.  Inspect 
the filters each day as part of the machine start-up, and clean them.  Replace the filter screen if 
necessary. 

Isocyanate  is  a  product  that crystallizes  with  ambient  moisture  or  freezing.    If  the  storage  and 
transfer is correct and the operating procedures are respected, the risk of contamination of the 
Isocyanate filter will be minimized. 

NOTE:

 Clean the Isocyanate inlet filter before the daily start-up; it should not be cleaned 

after the machine has been stopped for the day.  Immediately  beginning to project after 
cleaning  the  filter  reduces  the  risk  of  absorption  of  moisture  and  the  possibility  of 
contamination through the reaction with the solvent used in the cleaning operation.  

To check the product inlet filters, proceed as follows: 

a)  Disconnect  the  unit  from  the  power  supply  and  close  the  inlet  ball  valve  from  the  filter 

you wish to check.  

b)  Place  a  suitable  vessel  under  the  filter  to  collect  the  product  coming  out  on  removal.  

Carefully  loosen  the  filter  stopper  to  allow  the  product  to  be  emptied  into  the  vessel 
below. Completely unscrew the stopper. 

c)  Remove  the  seal,  the  spring  and  the  mesh  and  clean  it  all  with  the  solvent  used  for 

cleaning the gun.  Dry it all and check that the mesh is not obstructed. The holes in the 
mesh must  be  completely  free.    Replace  the  mesh  if  more  than  10%  of  the  surface  is 
obstructed.  

d)  Refit the mesh, the spring and the seal. Screw on the stopper. 

e)  Open  the  product  entry  valve  of  the  filter,  make  sure  there  are  no  leaks  and  proceed 

with the normal operation. 

 

Summary of Contents for Easy Spray















































Reviews: