Galaxy 635-DRM, Manual

Page: 1 / 10

GCS-HW-0117-SG-RDRWIR-QRG www.
galaxysys
.com Page 1 of 10
Galaxy Reader Wiring QRG
CONTENTS
1.0 Wiegand Reader – Cable Specs & Wiring Pin-out 1
2.0 ABA Reader – Cable Specs & Wiring Pin-out 1
3.0 Biometric Reader – General Cable Specs & Wiring 1
4.0 BridgePoint Reader
( NON
-
FICAM )
2
5.0 IDEMIA (Morpho) SIGMA BIO 5G 3
6.0 Invixium (IXM) Biometric Reader 3
7.0 SCM Reader ( NON-FICAM ) 4
8.0 STid Easyline Readers
(Weigand)
5
9.0
STid Reader w/Galaxy Config. 6
10.0 VERIDT
(FICAM Solution for TI)
7
11.0 VERIDT Stealth Readers
( NON-FICAM )
8
12.0 635-DRM Section Pinout for Reader & Relays 9
13.0
DOOR WIRING BLOCK DIAGRAM
10
1.0 Wiegand Reader - Cable Specs & Wiring
•
5-conductor, 22 AWG, overall shielded; max cable distance is 500 feet.
•
Reader will require separate power supply if the current draw is over 150 mA.
•
Ground the Drain-wire at one end only - at the DRM Board (GND).
•
Refer to reader manufacturer’s instructions for wiring (manufacturer's specs may supersede Galaxy specs).
635-DRM Terminal Functions (PN 20-0235-10) Wiegand Reader
LED (LED control line) LED Control
D 1 (Data 1) DATA 1
VDC (+12 VDC) ( for +5 VDC use Regulator PN 92-3001-05 ) VDC
GND (Power Supply Ground) GND
D 0 (Data 0) DATA 0
2.0 ABA Reader - Cable Specs & Wiring
•
5-conductor, 22 AWG, overall shielded; max cable distance is 500 feet.
•
Reader will require separate power supply if the current draw is over 150 mA.
•
Ground the Drain-wire at one end only - at the DRM Board (GND).
•
Refer to reader manufacturer’s instructions for wiring (manufacturer's specs may supersede Galaxy specs).
635-DRM Terminal Functions (PN 20-0235-10) ABA Reader
LED (LED control line) LED Control
D 1 (Data 1) DATA 1
VDC (+12 VDC) ( for +5 VDC use Regulator PN 92-3001-05 ) VDC
GND (Power Supply Ground)
GND
D 0 (Data 0) CLOCK
3.0 Biometric Reader - Cable Specs & Wiring
•
5-conductor, 22 AWG, overall shielded; max cable distance is 500 feet.
•
Cat-5e Ethernet cable for TCP/IP communication back to the server; max cable distance 300 feet.
•
Reader will require separate power supply if the current draw is over 150 mA.
•
Ground the Drain-wire at one end only - at the DRM Board (GND).
•
Refer to reader manufacturer’s instructions for wiring (manufacturer's specs may supersede Galaxy specs)
•
See next section for information on IDEMIA Morpho Sigma Readers.
635-DRM Terminal Functions (PN 20-0235-10) Wiegand Reader
LED (LED control line) LED Control
D 1 (Data 1) DATA 1
VDC (+12 VDC) ( Do not use for reader power! ) VDC
GND (Power Supply Ground) GND
D 0 (Data 0) DATA 0