background image

 

32 

Code?         OK
44232502

 

The activation code, which has also eight digits, has been accepted 
und the deep discharge counter has been reset to zero. No more 
warning message will be displayed any more until the next occurrence. 
 

Code?          X
5423250200

 

A wrong activation code has been entered and the code was not 
accepted. Switch off the G-Flame and repeat the procedure. 

 
 
 

21. Safety timer 

 
The safety timer will be started every time when the device is powered up and after exiting the menu. 
 

Safety Timer
Armend in:   15s

 

The timer counts down 15 seconds. 
 

 
The purpose of the safety timer is that the user can step back from the device before a flame effect 
can be initiated.  
 
The safety timer will be started no matter which control method has been selected. 
 
Note: While the safety timer is counting down you can terminate the sequence and directly invoke the 
menu by activating 'Mode'. 
 
 
 

22. The LED indicators 

 
This section describes the LED indicators which can be found right above the display: 
 
- LED 'Operation' 

(blue) 

- LED 'Flame'   

(yellow) 

- LED 'Charging' 

(green) 

- LED 'Low Battery' 

(red) 

 
 
 

22.1. The LED 'Operation' 

 
This blue LED displays the operating mode. While the safety timer is counting down or the device is in 
the menu this LED is continuously on. In this case no flame effect can be initiated.  
 
If the device is in receiving mode or ready to fire mode this LED is flashing. Only if this is the case a 
flame effect can be generated. 
 
 
 

22.2. The LED 'Flame' 

 
This yellow LED goes on as soon as the electromagnetic fuel valves are opened. 
 
If the Advanced wireless module is installed you can program step delays and so called atomic effects 
in the menu of the device or remotely via the wireless link. 
 
If an atomic effect has been initiated the LED goes on as soon as the electromagnetic valves are 
opening and not when the delayed ignition happens. 
 
When a step delay has been programmed and the firing command for this is being received by the 
device this LED starts to flash until the electromagnetic valves are opened. During a flame effect this 
LED is continuously on. 

Summary of Contents for PYROTEC G-Flame





























































Reviews: