manualshive.com logo in svg

Furuno DS-8500, Installation Manual

Share
Download
Furuno DS-8500 Installation Manual Download Page 63

3.  ADJUSTMENTS

3-19

3.5.5

SPEED TRIAL

Show the average ship’s speed for the 
specified period. Set the trial time then 
press the 

X

 key to start the trial. To stop 

the trial test, press the 

W

 key. If a USB 

flash memory is connected to the dis-
tributor unit, the distributor unit outputs 
the trial result.

Note: 

To output the results to a USB 

flash memory, connect a USB to the 
USB port in the distributor unit (shown the in figure above-right).

Item

Meaning

[RD-502 VERSION]

Version of RD-502

DAY/NT

 key

By pressing 

DAY/NT

 key of RD-502, changed figure color red 

→

 blue 

→

 red ….

T

 key

By pressing 

T

 key of RD-502, changed figure color red 

→

 blue 

→

 red ….

S

 key

By pressing 

S

 key of RD-502, changed figure color red 

→

 blue 

→

 red ….

MENU/ESC

 key

Go back to [TEST] sub menu.

Item

Meaning

Range

[TRIAL TIME]

Trial time (min)

[10] to [60]

[EXPORT]

Set [ON] to export the measurement result to 
an USB device.

[ON] or [OFF]

[TIME]

Elapsed time from trial start

[00 min 00.0 sec] to 
[60 min 00.0 sec]

01 . 01

DST board 65P6110

LIF board 

65P6111

(option)

USB port

USB port

: Measuring speed

: Stop measurement

Summary of Contents for DS-8500































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands