manualshive.com logo in svg

Furuno DS-8500, Installation Manual

Share
Download
Furuno DS-8500 Installation Manual Download Page 27

1.  MOUNTING

1-21

25. Put the fixing plate (21) between the shaft (5) and gland (19). Fasten the plate with 

two sets of M8 hex. bolt (13) and M8 spring washer (14).
Check the clearance between the fixing plate (21) and the lock ring (6). If the clear-
ance is more than 3 mm, be sure to check that the hollow side of the flange (3) is 
aligned with the projection on the transducer (1).

26. Check that all bolts are fastened tightly.
27. Paint the ball valve (20) and the flange (3) the same color as ship’s body. Paint 

only gray-colored areas; for other parts, seal with masking tape. Remove the tape 
when the paint dries.

<How to open/close the ball valve>

To open/close the ball valve, attach the supplied handle to the square projection then 
change the stopper position.

1. Remove the fixing plate as shown figure below then pull the shaft assembly up.

0-3 mm

Lock ring (6)

Gland (19)

Fixing plate (21)

Hex. bolt (13)(M8x30)
Spring washer (14)(M8)

1

䠅

 Remove two 

hex socket  
screws (M8).

2

䠅

  Slide the fixing 

plate to remove 
it.

3

䠅

  Remove two hex 

screws (M8).

Fixing plate

Fixing plate

Shaft 
assembly

Shaft 
assembly

Summary of Contents for DS-8500































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands