manualshive.com logo in svg

Furuno DS-8500, Installation Manual

Share
Download
Furuno DS-8500 Installation Manual Download Page 25

1.  MOUNTING

1-19

15. Fasten the gland (19) to the top of the shaft (5).

16. Apply the Liquid Gasket TB1121 to both sides of the gasket2 (18), and put it on 

the ball valve (20).

17. Put the shaft on the gasket2 (18), and align the hollow side on the flange (3) with 

the projection of the transducer (1).

18. Remove three M8 hex. bolts (13) and three M8 spring washers (14) from the lock 

ring (6) to free the shaft (5).

19. Fasten the flange (4) loosely with the M16 hex. bolt (12), M16 nut (10) and M16 

flat washer (11).

20. Insert the shaft so the projection on the transducer (1) fits in the groove on the 

flange (3). Move the shaft up and down by hand to confirm that it moves smoothly.

Gland (19)

Flat washer (8)

Gasket (7)

Flat washer (8)

The projection on the transducer (1)

Flange (4)

Hex. nut (15)(M4x16)
Seal washer (16)(M4)

Apply Liquid Gasket (TB1121) here.

The fore mark on the shaft

Check that they 
are aligned.

Summary of Contents for DS-8500































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands