manualshive.com logo in svg

Furuno DS-8500, Installation Manual

Share
Download
Furuno DS-8500 Installation Manual Download Page 61

3.  ADJUSTMENTS

3-17

[DS-8520 TEST (2/3)]: page 2

Item

Meaning

Range

[SERIAL NO.]

Serial number of transceiver 
unit

[000000] to [999999]

[STA
RTE
R 
VER
SIO
N]

Starter version of transceiver 
unit

[6550311-01.01] to 
[6550311-99.99]

[BO
OT 
VER
SIO
N]

•  Upper: Booter version used 

for start-up of the transceiv-
er unit .

•  Lower: Booter version not 

used (backup) for start-up of 
the transceiver unit

[6550312-01.01] to 
[6550312-99.99]

[APPLICATION 
VERSION]

Application version of trans-
ceiver unit.

[6550313-01.01] to 
[6550313-99.99]

[FP-
GA 
VER
SIO
N]

FPGA version

[6550314-01.01] to 
[6550314-99.99]

[MAI
N 
VER
SIO
N]

Main board version

[0] to [E], [–] (NG)

[TRX VERSION]

TRX board version

[0] to [E], [–] (NG)

[ROM/RAM]

Result of ROM test/Result of 
RAM test

[OK] or [NG]

[BUBBLE]

Value of bubble effects
([5] or less ideally)

[0] to [255]

X

 key

Go to page 2 of the [DS-8520 TEST].

MENU/ESC

 key

Go back to [TEST] sub menu.

Item

Meaning

Range

[IP ADDRESS]

IP address of transceiver unit

[000.000.000.000] to 
[255.255.255.255]

[SUBNET MASK]

Subnet mask of transceiver unit

[000.000.000.000] to 
[255.255.255.255]

[GATEWAY]

Gateway of transceiver unit

[000.000.000.000] to 
[255.255.255.255]

192 . 168 . 200 . 001
255 . 255 . 255 . 000
000 . 000 . 000 . 000
FF : FF : FF : FF : FF : FF
S2 : 0001  S3 : 0000  S5 : 0000
0 . 04NM

Summary of Contents for DS-8500































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands