manualshive.com logo in svg

Furuno DS-8500, Installation Manual

Share
Download
Furuno DS-8500 Installation Manual Download Page 51

3.  ADJUSTMENTS

3-7

[FORMAT]

Select the format for LAN connection, [IEC Ed.4] or [IEC Ed.5] (default: [IEC Ed.5]).

[TRANSMISSION GROUP SETUP]

Open the [TRANSMISSION GROUP SETUP] window to set the IP address or port.

[IP ADDRESS]: Set the IP address, [000.000.000.000] to [255.255.255.255] (default: 
[239.192.000.004]).

[PORT]: Set the port, [00000] to [65535] (default: [60004]).

Note: 

To comply with the IEC standards, the following conditions are required. 

•  [IP ADDRESS]: Set between [239.192.000.001] and [239.192.000.064].
•  [PORT]: Set between [60001] and [60064]

3.3

[SIMULATION] sub menu

The simulation mode displays and outputs internally specified speed data. This mode 
can be used for simulation and to check output to external equipment. "SIM" appears 
on the screen when the simulation mode is active.

On the main menu, select [EQUIPMENT] 

→

[SIMULATION] to open the [SIMULA-

TION] sub menu.

SIM

[EQUIPMENT] sub menu

Option menus

Summary of Contents for DS-8500































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands