manualshive.com logo in svg

Furuno DS-8500, Installation Manual

Share
Download
Furuno DS-8500 Installation Manual Download Page 19

1.  MOUNTING

1-13

20. Use the M16 hex. bolt (12), M16 nut (10) and M16 spring washer (11) to fasten 

the flange (4) loosely.

21. Insert the shaft so the projection on the transducer fits in the groove on the flange 

(3). Move the shaft up and down by hand to confirm that it moves smoothly.

22. Tighten the M16 nut(8 pcs.) on the gate valve (20).

23. Loosely fasten two sets of M8 hex. bolt (13) and M8 spring washer (14) at the top 

side of the lock ring (6).

24. Tightly fasten the M8 hex. bolt (13) tightly and the M8 spring washer (14) at the 

lateral side of the lock ring.

25. Loosely fasten two sets of M8 hex. bolt (13) and M8 spring washer (14) fastened 

at step 23.

26. Put the fixing plate (21) between the shaft (5) and gland (19). Fasten the plate with 

two sets of M8 hex. bolt (13) and M8 spring washer (14). Check the clearance be-
tween the fixing plate (21) and the lock ring (6). If the clearance is more than 3 

A

Hex. bolt (13)(M8x30)
Spring washer (14)(M8)

Lock ring (6)

Flange (4)

Shaft (5)

Transducer (1)

Hex. bolt (12)(M16x60)

Gasket2 (18)
(Apply the Liquid Gasket 
TB1121 to both sides.)

Nut (10) (M16)
Spring washer (11)(M16)

Ball valve (20)

Spacer (3)

Align the hollow side 
of the spacer (3) with 
the projection on the 
transducer (1).

Transducer (1)

Spacer (3)

View from "A"

Hex. bolt (13)(M8x30)
Spring washer (14)(M8)

A

B

Hex. bolt (13)(M8x30)
Spring washer (14)(M8)

1. Fasten "A" loosely (step 22)
2. Fasten "B" tightly (step 23)
3. Fasten "A" tightly (step 24)

Hex. bolt (13)(M8x30)
Spring washer (14)(M8)

Summary of Contents for DS-8500































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands