manualshive.com logo in svg

Furuno DS-8500, Installation Manual

Share
Download
Furuno DS-8500 Installation Manual Download Page 57

3.  ADJUSTMENTS

3-13

[DS-8500 TEST (1/4)]: page 1

[DS-8500 TEST (2/4)]: page 2

Item

Meaning

Range

[SERIAL NO.]

Serial number of display unit

[000000] to [999999]

[STA
RTE
R 
VER
SIO
N]

Starter version of display unit

[6550302-01.01] to 
[6550302-99.99]

[BO
OT 
VER
SIO
N]

•  Upper: Booter version used for start-up 

of display unit.

•  Lower: Booter version not used (back-

up) for start-up of display unit

[6550303-01.01] to 
[6550303-99.99]

[APPLICATION 
VERSION]

Application version of display unit

[6550304-01.01] to 
[6550304-99.99]

[ROM/RAM]

Result of ROM test/Result of RAM test

[OK] or [NG]

[PORT]

Result of serial port

[OK] or blank

[LCD TOTAL 
TIME]

Total operation hours of LCD.

[0] to [999999] (h)

[12 VOLT]

Voltage value of display unit

[0.0] to [99.9] (V)

X

 key

Go to page 2 of the [DS-8500 TEST].

MENU/ESC

 key

Go back to [EQUIPMENT] sub menu.

Item

Meaning

Range

[LCD BACK 
LIGHT]

Automatic brilliance test of LCD is started.
The brilliance is changed according to the dis-
played value.

[0] to [17] 
(First value: [17])

[KEY BACK 
LIGHT]

Brilliance of key back light

[0] to [17] 
(default: [0])

X

 key

Go to page 3 of the [DS-8500 TEST].

MENU/ESC

 key

Go back to [EQUIPMENT] sub menu.

Summary of Contents for DS-8500































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands