manualshive.com logo in svg

Furuno DS-8500, Installation Manual

Share
Download
Furuno DS-8500 Installation Manual Download Page 24

1.  MOUNTING

1-18

10. Remove the Jubilee clip located at the base of the transducer (1) cable and four 

M4 flat-head Phillips screws at the top side of the transducer (1).

11. Pass the transducer cable through the shaft from the flange side.
12. Apply the Liquid Gasket TB1121 to the top side of the transducer evenly.
13. Apply the Liquid Gasket TB1121 to the thread part of hex. bolt (15) with seal wash-

er (16) and use them to fasten the transducer.
Check that the fore mark on the shaft is aligned with the projection at the bottom 
of the transducer.

14. Pass the flat washer (8), gasket (7), washer (8), and the gland (19) onto the trans-

ducer cable.

Jubilee clip

Jubilee clip

Do not remove 
this screw.

Remove these 
four screws. 

Removing Jubilee clip

Removing flat-head Phillips screws

The fore mark on the shaft

Align them.

The projection on the transducer

Bottom view

Summary of Contents for DS-8500































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands