manualshive.com logo in svg

Fujitsu PRIMERGY RX220, Operating Manual, Page: 7 / 87

Share
Download
Fujitsu PRIMERGY RX220 Operating Manual Download Page 7

RX220

Operating Manual

7

Introduction

Overview of the Documentation

–

"ServerView Suite" includes the 

ServerStart

 CD, the 

ServerBooks

 CD and the 

ServerSupport

 CDs. The PDF file of the user manual "PRIMERGY 

ServerView Suite - ServerStart" is also available on the 

ServerBooks

 CD.

I

If you need a backup of the 

ServerBooks

 CD, send the details of your 

server via email address: 

[email protected]

.

–

"Global Array Manager Client Software User’s Guide" (PDF file available on 
the 

ServerBooks

 CD)

–

"Global Array Manager Server Software User’s Guide" (PDF file available on 
the 

ServerBooks

 CD)

–

"Integrated Mirroring User’s Guide" (PDF file available on the 

ServerBooks

 

CD)

–

"RX220 Options Guide" (PDF file available on the 

ServerBooks

 CD)

Further sources of information

–

technical Manual for the corresponding rack

–

manual for the monitor

–

manual for 

ServerView server management

–

manual for the remote test and diagnostic system 

RemoteView

–

documentation for the boards and drives

–

operating system documentation

–

information files of your operating system

(see also 

“Related Publications” on page 75

).

Summary of Contents for PRIMERGY RX220
























































































Reviews:

No comments