manualshive.com logo in svg

Fujitsu PRIMERGY RX220, Operating Manual, Page: 51 / 87

Share
Download
Fujitsu PRIMERGY RX220 Operating Manual Download Page 51

RX220

Operating Manual

51

Perparation for Use and Operation

Configuring the Server

5.3

Configuring the Server and Installing the 
Operating System

This section contains information about configuring the server and installing the 
operating system.

I

Make sure that the energy saving functions are 

disabled

 in the 

BIOS Setup

 

(„D2130 Setup Utility for RX220“) during server operation.

5.3.1

Configuring the SATA RAID controller

The server is equipped with an onboard SATA RAID controller with "Integrated 
Mirroring" (IME) functionality. You may configure the RAID either before 
running ServerStart or with 

ServerStart

. It is recommended to use ServerStart.

Configuring the SATA RAID controller is either performed via the BIOS configu-
ration utility (calling CTRL-F during BIOS POST) or with the ServerStart CD 
using GAM (Global Array Management). More information is contained in the 
controller documentation on the ServerBooks CD in section "controllers" (see 
also 

“Related Publications” on page 75

).

I

Note on 

SATA-IDs

:

Please note that the SATA-IDs for the hot-plug hard disk drives are 
permanently assigned (from left to right).

I

Descriptions of operating systems not covered in the RAID controller 
manual are provided in the appropriate readme files on the driver 
diskettes.

Summary of Contents for PRIMERGY RX220
























































































Reviews:

No comments