manualshive.com logo in svg

Fujitsu PRIMERGY RX220, Operating Manual, Page: 47 / 87

Share
Download
Fujitsu PRIMERGY RX220 Operating Manual Download Page 47

RX220

Operating Manual

47

Preparation for Use and Operation

Operating and Indicator Elements

5.1.2

The Rear

Figure 11: Connection panel: indicators

1

LAN activity indicator (green)

Flashes green when a LAN transfer occurs.

Does not light if there is no LAN connection available.

Lights if there is a LAN connection available.

2

LAN transfer rate indicator (dual color)

No function. Does not light.

3

Global Error indicator (amber)

Does not light when the system is ok. No service incident or critical event 
has occurred.

Flashes amber when a critical event has occurred. Users can check 

BIOS Setup

, system event log or via 

ServerView

 for event details. The 

indicator also flashes in standby mode.

Lights amber when a prefailure event has been recognized. Users can 
check system event log or via 

ServerView

 for event details. The indicator 

also lights in standby mode.

If the event is still acute after a power failure, the indicator is activated 
after the restart. 

Table 4: Indicators on the rear

1

2

1

2 3 4

Summary of Contents for PRIMERGY RX220
























































































Reviews:

No comments