manualshive.com logo in svg

Fujitsu PRIMERGY RX220, Operating Manual, Page: 50 / 87

Share
Download
Fujitsu PRIMERGY RX220 Operating Manual Download Page 50

50

Operating Manual

 RX220

Switching the Server ON and OFF

Preparation for Use and Operation

Server in standby mode

The power-on indicator (position 11 in 

figure 9 on page 43

) flashes green. The 

CPU, the system fans and the drives have been slowed down.

Ê

Shut down all RGB applications.

Ê

Press any button to return to normal operation.

Other ON/OFF options

In addition to the ON/OFF button, the server can be switched ON and OFF in 
the following ways:

–

Specified switch-on time/switch-off time

The server is switched ON or OFF at a time specified in the 

ServerView

 

program.

–

Ring indicator

The server is switched ON via an internal or external modem. 

–

Wake On LAN (WOL)

The server is switched ON by a command via the LAN (Magic Package).

–

After power failure

The server automatically reboots following a power failure (depending on the 
BIOS settings).

–

Power override function

The system can be switched OFF by pressing the ON/OFF button for about 
4 to 5 seconds.

V

CAUTION!

Data loss may occur!

–

IPMI

The server is switched ON by an IPMI console (via the serial COM1 port or 
via the RJ45 LAN port).

Summary of Contents for PRIMERGY RX220
























































































Reviews:

No comments