Fujitsu General ASHG07KPCE Service Manual Download Page 116 | Manualshive

Page: 116 / 132

background image

6-1. Defrost operation in heating operation stopped

If the outdoor unit is frosted when stopping the heating operation, it stops after performing the auto-
matic defrosting operation.
In this time, if the indoor unit operation lamp flashes slowly (6 sec on/2 sec off), the outdoor unit al-
low the heat exchanger to defrost, and then stop.

•

Triggering condition

When all of the following conditions are satisfied in heating operation

– Compressor operation integrating time: 30 minutes or more
– Compressor continuous operation time: 10 minutes or more
– Outdoor unit heat exchanger temperature: -4°C or less

•

Release condition

The defrost operation is released when either one of the conditions below is satisfied.

Outdoor unit heat exchanger temperature
(after 1 minute or later since compressor start)

16°C or more

Compressor operation time

15 minutes

6-1. Defrost operation in heating operation stopped

- (04-22) -

6. Defrost operation control

CONTROL AND

FUNCTIONS

CONTROL AND

FUNCTIONS

«
...
114
115
116
117
118
...
»

Summary of Contents for General ASHG07KPCE





































































































































Reviews:

No comments

Related manuals for General ASHG07KPCE

Brand: Daikin Pages: 7

Brand: Daikin Pages: 6

Brand: Daikin Pages: 24

Brand: Daikin Pages: 28

Brand: Daikin Pages: 34

Brand: Daikin Pages: 44

Brand: Daikin Pages: 44

Brand: Daikin Pages: 13

Brand: Daikin Pages: 22

Brand: Daikin Pages: 134

Brand: Daikin Pages: 274

Brand: Daikin Pages: 16

Brand: Haier Pages: 57

Brand: Panasonic Pages: 198

S-15MY2E5A CZ-KPY3A

Brand: Panasonic Pages: 36

Brand: Panasonic Pages: 52

Brand: Daikin Pages: 32

Brand: GE Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands