manualshive.com logo in svg

Fujitsu fi-4860C, Operator'S Manual

Share
Download
Fujitsu fi-4860C Operator'S Manual Download Page 99

3-9

3.3 Cleaning the Rollers

3

DAIL

Y CARE

6.

When [Hopper Empty] is displayed, press 

(Stop button). 

7.

Place the same cleaning sheet on the hopper table with adhesive side up 
by aligning the right side with the hopper guide. Press 

(Start button), 

then the cleaning sheet is fed. 

8.

When "Hopper Empty" is displayed, press 

(Stop button). 

9.

Remove the protective paper from a new cleaning sheet and place it with 
the adhesive side face down on the hopper table, aligning the left side 
with the hopper guide. Press 

 (Start button), then the cleaning sheet 

is fed. 

Repeat steps 6 through 8. When the cleaning is completed turn off the power.

Summary of Contents for fi-4860C


































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands