manualshive.com logo in svg

Fujitsu fi-4860C, Operator'S Manual

Share
Download
Fujitsu fi-4860C Operator'S Manual Download Page 20

●

xviii

Do not use aerosol sprays near the scanner.

Avoid any contact when the scanner is in use.

Disconnect the power plug from the power outlet when the scanner is 
not used for a long period of time.

Do not install the scanner in the direct sunlight.

Do not use aerosol sprays to clean the scanner. Aerosol sprays cause dirt 
and dust to enter the scanner, resulting in scanner failure and malfunction.

Avoid touching any part of the scanner mechanism or paper when 
scanning as this may cause injuries.

When the scanner is not used for a long period of time, be sure to 
disconnect the power plug from the power outlet for safety.

Do not install the scanner in the direct sunlight or near heating apparatus. 
Doing so might cause excessive heat to build up inside the scanner, 
causing fire or scanner trouble. Install the scanner in a well-ventilated 
location.

Summary of Contents for fi-4860C


































































































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands