Fujitsu fi-4860C Operator'S Manual Download Page 259

Page: 259 / 321

7-53

7.3 Setup Mode Details

AT
O

PA
N

L M

23. Setting Baud rate of TPS interface

1) Press

(Next button) or

(Previous button) and let LCD display

<Screen23>.

2) At <Screen23>, press

(Left arrow button) or

(right arrow button) and

select Baud rate.

Baud rates available are as follows:

(1) 19200 bps
(2) 9600 bps
(3) 4800 bps
(4) 2400 bps

By pressing

(Left arrow button), selection moves from (4) to (1).

By pressing

(Right arrow button), selection moves from (1) to (4).

3) Press

(Enter button) to confirm the setting.

Press

(Exit button) at the end and the LCD display goes back to [Ready]

screen.

HINT

The blinking item is the one selected.

HINT

Baud rate at 9600 bps is recommended.

Summary of Contents for fi-4860C


































































































































































































































































































































Search results

Summary of Contents for fi-4860C

Reviews:

Brands by name

Popular brands

Fujitsu fi-4860C, Operator'S Manual

Search results

Summary of Contents for fi-4860C

Reviews:

Brands by name

Popular brands