Fujitsu fi-4860C Operator'S Manual Download Page 44

Page: 44 / 321

1-18

1.7 Loading Documents on the Hopper

1.7 Loading Documents on the Hopper

Straighten the edges of the documents

1) Straighten both sides of the document stack.

Fan the documents

1) Take a stack of documents with thickness of 15mm to 20mm (1/2 to 3/4

inch).

2) Hold both ends and bend the documents into an arch.

3) Firmly holding the document with both hands, bend back the document as

follows so that the bent section rises up in the middle of the document as
follows.

4) Repeat steps 1) to 3) for a few times.

5) Rotate the document 90 degrees, and fan again.

15 to 20mm

Summary of Contents for fi-4860C


































































































































































































































































































































Search results

Summary of Contents for fi-4860C

Reviews:

Brands by name

Popular brands

Fujitsu fi-4860C, Operator'S Manual

Search results

Summary of Contents for fi-4860C

Reviews:

Brands by name

Popular brands