Fujitsu ABHG54KRTA Service Manual Download Page 23

Page: 23 / 154

5. Optional parts

5-1. Indoor unit

Controllers

Exterior

Part name

Model name

Summary

Wired remote

controller

UTY-RNRGZ*

Easy finger touch operation with LCD
panel. Backlit LCD enables easy
operation in a dark room.
Wire type: Non-polar 2-wire

Wired remote

controller

UTY-RLRG

High visibility and easy operation.
Room temperature can be accurately
controlled using the built-in thermo
sensor.
Wire type: Non-polar 2-wire

Compact wired

remote

controller

UTY-RCRGZ1

Compact body and easy operation.
Room temperature can be accurately
controlled using the built-in thermo
sensor.
Wire type: Non-polar 2-wire

Simple remote

controller

UTY-RSRG

Compact remote controller
concentrates on the basic functions
such as Start/Stop, fan control,
temperature setting, and operation
mode.
Wire type: Non-polar 2-wire

Simple remote

controller

UTY-RHRG

Compact remote controller
concentrates on the basic functions
such as Start/Stop, fan control, and
temperature setting.
Wire type: Non-polar 2-wire

IR receiver kit

with wireless

remote

controller

UTY-LBTGH

Unit control is performed by wireless
remote controller.

NOTE:

Available functions may differ by the remote controller. For details, refer to the operation
manual.

5-1. Indoor unit

- (02-9) -

5. Optional parts

TECHNICAL DATA

AND PARTS LIST

TECHNICAL DATA

AND PARTS LIST

Summary of Contents for ABHG54KRTA



























































































































































Search results

Summary of Contents for ABHG54KRTA

Reviews:

Related manuals for ABHG54KRTA

Brands by name

Popular brands

Fujitsu ABHG54KRTA, Service Manual

Search results

Summary of Contents for ABHG54KRTA

Reviews:

Related manuals for ABHG54KRTA

Brands by name

Popular brands