Frenic 5000VG7S Series, Instruction Manual

Page: 53 / 97

5-9
Communication
address
Fcode
485
number
Link number
Function name Setting range
h40 428h ( h) RS485
(Protocol)
0 to 1 to 2
0 : FUJI inverter protocol
1 : SX bus (FUJI private link) protocol
2 : Modbus RTU protocol
Please set 1 (SX bus protocol) when you use the PC
loader of the VG7 exclusive use.
h41
429h 209( D1 h) Torque
reference
selection
0 to 5
0 : Internal ASR output
1 : AI terminal input (T-REF)
2 : DIA card input
3 : DIB card input
4 : Link input
5 : PID
h42 42Ah 210( D2 h) Torque current
reference
selection
0 to 4
0 : Internal ASR output
1 : AI terminal input (IT-REF)
2 : DIA card input
3 : DIB card input
4 : Link input
h43 42Bh 211( D3 h) Magnetic flux
reference
selection
0 to 3
0 : Internal calculation value
1 : AI terminal input (MF-REF)
2 : Function setting value (H44)
3 : Link input
h44
42Ch 212( D4 h) Magnetic flux
reference
value
10 to 100 %
h46 42Eh 215( D7 h) Observer
(Mode select)
0 to 2
0 : Inactive
1 : Active (load disturbance observer)
2 : Active (oscillation suppressing observer)
h47 42Fh 216( D8 h) (P-gain 1)(M1) 0.00 to 1.00 (times)
h48
430h ( h) (P-gain 2)(M2) 0.00 to 1.00 (times)
h49 431h 217( D9 h) (I-gain 1)(M1) 0.005 to 0.100 to 1.000 s
h50 432h ( h) (I-gain 2)(M2) 0.005 to 0.100 to 1.000 s
h51 433h 218( DA h) Load inertia
M1
0.01 to 50.000 (kg.m 2 )
(Target ROM No. H1/20064 or later)
h52 434h ( h) Load inertia
M2
0.01 to 50.000 (kg.m 2 )
(Target ROM No. H1/20064 or later)
h53 435h 213( D5 h) Line speed
feedback
selection
0 to 3
0 : Line speed disabled
1 : Line speed (analog input) (AI-LINE)
2 : Line speed (digital input) (PG(LD))
3 : High level selected signal
h55 437h ( h) Zero speed
control (Gain)
0 to 5 to 100 (times)
h56
438h ( h) Completion
range
0 to 100 (pulse)
h57 439h ( h) OU alarm
prevention
0 to 1
0 : Inactive
1 : Active
h58 43Ah ( h) OC alarm
prevention
0 to 1
0 : Inactive
1 : Active
h60 43Ch ( h) Load adaptive
control
function 1
0 to 3
0 : Inactive
1 : Method 1
2 : Method 2
3 : Method 3
h61 43Dh ( h) Load adaptive
control
function 2
0 to 1
0 : Winding up on forward rotation
1 : Winding down on forward rotation
h62 43Eh ( h) Winding up
speed
0.0 to 999.9 m/min
h63 43Fh ( h) Counter weight 0.00 to 600.00 (t)
h64 440h ( h) Safety
coefficient (for
rated torque)
0.50 to 1.00 to 1.20
h65
441h ( h) Machine
efficiency
0.500 to 1.000
h66 442h ( h) Rated loading 0.00 to 600.00 (t)
h68 444h ( h) Alarm data
delete
0 to 1
If these tuning are finished, this data code returns to 0.
h70 446h ( h) Reserved 1 0 to 9999
0 : Standard
1 : Lift
2 to 9999 : Undecided
Communication
address
Fcode
485
number
Link number
Function name Setting range
h71 447h ( h) Reserved 2 0 to 6
It is not necessary to set usually.
If these tuning are finished, this data code returns to 0.
0 : Inactive
1 : ACR system tuning
2 : Voltage gain tuning (execution without connecting
motor)
3 : Voltage sensor offset tuning
4 : Current sensor balance tuning
5 : Magnet pole position tuning (for SM driving)
6 : Shunt resistor gain tuning
h72 448h ( h) Reserved 3 0 to 9999
0 : standard
1 to 9999 : Undecided
h73 449h ( h) Reserved 4 0 to 9999
0 : standard
1 to 9999 : Undecided
A: Alternative Motor Parameters
Communication
address
Fcode
485
number
Link number
Function name Setting range
a01 501h ( h) M2-Control
method
0 to 1
M2 is an induction motor only for the vector control.
0 : Vector control with PG
1 : Vector control without PG
a02 502h ( h) M2-Rated
capacity
0.00 to 500.00kW at F60=0
0.00 to 600.00HP at F60=1
a03 503h ( h) M2-Rated
current
0.01 to 99.99A
100.0 to 999.9A
1000 to 2000A
a04 504h ( h) M2-Rated
voltage
80 to 999 V
a05 505h ( h) M2-Rated
speed
50 to 1500 to 24000 r/min
a06 506h ( h) M2-Maximum
speed
50 to 1500 to 24000 r/min
a07 507h ( h) M2-Poles 2 to 4 to 12 (poles)
a08 508h ( h) M2-%R1 0.00 to 30.00 %
a09 509h ( h) M2-%X 0.00 to 50.00 %
a10 50Ah ( h) M2-Exciting
current
0.01 to 99.99A
100.0 to 999.9A
1000 to 2000A
a11 50Bh ( h) M2-Torque
current
0.01 to 99.99A
100.0 to 999.9A
1000 to 2000A
a12 50Ch ( h) M2-Slip
(Driving)
0.001 to 10.000 Hz
a13 50Dh ( h) M2-Slip
(Braking)
0.001 to 10.000 Hz
a14 50Eh ( h) M2-Iron loss
coefficient 1
0.00 to 10.00 %
a15 50Fh ( h) M2-Iron loss
coefficient 2
0.00 to 10.00 %
a16 510h ( h) M2-Iron loss
coefficient 3
0.00 to 10.00 %
a17 511h ( h) M2-Magnetic
saturation
coefficient 1
0.0 to 100.0 %
a18 512h ( h) M2-Magnetic
saturation
coefficient 2
0.0 to 100.0 %
a19
513h ( h) M2-Magnetic
saturation
coefficient 3
0.0 to 100.0 %
a20
514h ( h) M2-Magnetic
saturation
coefficient 4
0.0 to 100.0 %
a21 515h ( h) M2-Magnetic
saturation
coefficient 5
0.0 to 100.0 %
a22 516h ( h) M2-Secondary
time constant
0.001 to 9.999 s
a23 517h ( h) M2-Induced
voltage
coefficient
0 to 999 V
a24 518h ( h) M2-R2
correction
coefficient 1
0.000 to 5.000
a25 519h ( h) M2-R2
correction
coefficient 2
0.000 to 5.000
Underline indicates a factory setting.
Items without underline have different factory settings according to capacity.
You can change the setting of a function indicated by during operation.
You should stop operation to change the setting of other functions.