MODEL: P LSLW
50
MODEL: P LSLW
50
06
07
HTTP://WWW FREEMANTOOLS COM 1-888-669-5672
.
.
HTTP://WWW FREEMANTOOLS COM 1-888-669-5672
.
.
Use only those fasteners recommended
for use with this tool. Fasteners not
identified for use with this tool by the tool
manufacturer are able to result in a risk of
injury to persons or tool damage when
used in this tool.
WARNING:
!
The tool may fire when it first connected
to the air source. Always connect the tool
to the air source before loading fasteners
to prevent injury from unintended cycling.
Always make sure the tool's magazine is
empty at the beginning of each work
session, before connecting to an air
source.
WARNING:
!
OPERATION
The tool is shipped with the Arm
part detached
from the Main body part.
(A)
PREPARE THE TOOL
Set the Arm(A) against the Handle .
Wrench-tighten the Nuts(B) until the Arm(A) and
Handle (C) are secured and the Arm
is locked
against Handle
.
(A)
(C)
Follow these instructions to prepare the tool for
using.
1.
2.
Nut (B)
Hex. Bolt
Arm(A)
Handle
(C)
Prepared
Flooring Nailer
LOADING L CLEAT NAILS
Connect the tool to the air source.
Press down on the Latch Button(F). Pull the
Magazine Cover (D) back to the end of the
magazine.
Place full clip of desired fasteners into magazine
from the side. Up to 100 cleat nails can be
loaded into magazine. Be noted that, when
loading the L cleat nails, the side with the L head
should be in the left of the Magazine Pusher(E).
Push the Magazine Cover(D) forward until
Magazine Pusher(E) pops up.
1.
2.
3.
4.
L Cleat Head
Direction
Magazine Pusher
(E)
Magazine
Cover
(D)
LOADING STAPLES
Connect the tool to the air supply.
Press down the Latch Button(F), the pull the
Magazine Cover(D) back to the end of the
magazine.
Place a full clip of 1/2" crown staples in the
magazine from the top. Up to 90 staples can be
loaded into magazine.
Push the Magazine Cover(D) forward until the
Magazine Pusher (E) pops up.
1.
2.
3.
4.
Load staples
from the top
CHANGE THE FOOT PLATE
The tool is equipped with a factory pre-installed
3/4" Foot Plate(G). And an additional uninstalled
5/8" foot plate. To change the plate:
Disconnect the tool from the air source.
Empty the magazine completely.
Fire the tool into a piece of scrap wood to
ensure there is no compressed air or fasteners
left in the tool.
Set the tool on its side to expose the four
Screws(H).
Remove the four Screws(H), then, remove the
foot plate.
Align the four screw holes in the replacement
foot plate with the four threaded mounting
holes.
Using the four screws you removed just now,
secure the replacement foot plate to the tool.
Ensure the correct Foot Plate is installed by
firing into a scrap piece of flooring and checking
for proper fastener placement.
Disconnect the tool from the air source
whenever changing the foot plate.
Make sure there is no fastener in the
magazine before changing the foot plate.
WARNING:
!
⒈
⒉
⒊
⒋
⒌
⒍
⒎
⒏
Screws(E)
Foot plate(D)
The amount of air pressure required depends
on the size of the fasteners and the workpiece
material.
Begin testing the depth of drive by driving a test
nail into the same type of workpiece material
used for the actual job.
Drive a test fastener with the air pressure set at
90-95psi.
Raise or lower the air pressure to find the lowest
setting that will perform the job with consistent
results.
SETTING THE AIR PRESSURE
If any parts are missing, do not operate
this tool until the missing parts are
replaced. Before using this tool, make
sure the arm part and the main body part
are screwed together tightly. Failure to do
so could result in possible serious
personal injury.
WARNING:
!
Latch Button(F)
Magazine
cover
(D)
Latch Button(F)
Magazine
pusher
(E)
⒈
⒉
⒊
⒋
