47
Adjusting the Source Channel
Tips: Adjusting the PAN Setting of the Source Channel
It is possible to set the PAN according to the sound
source of the source channel when recording to two
tracks. Press the
[PAN]
key to switch to the PAN setting
display. Select the channel to adjust the PAN setting
with the
[CH STATUS/CH SEL]
key. Then use the
[JOG]
dial to optionally set the PAN setting.
The final REC Level (REC BUSS Master Level) is adjusted
according to the earlier mentioned procedures.
The system is ready to record after you have com-
pleted the above procedures.
Record
1. Locate the time to record on the VF160.
2. Press the [PLAY] key while the [RECORD] key is depressed
to start recording.
The [CH STATUS/CH SEL] key and the [RECORD] key of
ch7& 8 lights up RED, indicating that recording is taking
place.
3. Press the [STOP] key when the recording is completed, to stop
the VF160.
"
Please Wait
" appears on the LCD and then returns to the
Normal Display.
This completes recording the sound source of inputs
A to H on tracks 7 and 8.
Tips: UNDO/REDO
By pressing the
[UNDO/REDO]
key after recording, the re-
cording is undone and the track returns to the pre-REC
state where there is no recording (UNDO). By pressing
the
[UNDO/REDO]
key again, the recording on two tracks
are redone to the post-REC state (REDO). The UNDO/
REDO feature is available for all recordings.
Play
1. Locate the time in which recording was started (REC start time).
2. Press the [PLAY] key to play the VF160.
Adjust the play level of tracks 7 and 8 with the ch7 & 8 faders
to check (listen to) the sound recorded.
Preparing to Record
<Note>
If input signals are started for ch9-16 faders, the play
sounds of the corresponding track can no longer be
heard and you cannot go to the READY (REC) state.
Press the [BUSS-SOURCE] key. (GREEN: Flashing)
Press the [CH STATUS/CH SEL] key of ch 9-16. (ORANGE:
Flashing)
Signals of input A to H can now be sent to REC BUSS.
Press the [BUSS-REC TRK] key (RED: Flashing).
Press the [CH STATUS/CH SEL] key of ch7 and 8 (RED:
Flashing).
Track 7 and 8 will proceed to the "
RDY
(Ready)" state.
Press the [EXIT/NO] key to return to the Normal Display.
1
Connect to the [INPUT] jack the sound source to record.
Press the [INPUT SEL] key.
Press the [CH STATUS/CH SEL] key of ch9-16 to switch ch
9-16 to "INPUT".
Ch9-16 is ready to start signals of input A to H.
2
3
4
5
6
7
8
9
Press the [RECORD] key and set tracks 7 and 8 to the input
monitor (RED: Flashing).
As in the earlier case, the monitor sound is output at this
stage. Adjust the volume of the monitor sound with the
[MON OUT]
or
[PHONES]
knob.
Set the ch7&8 fader, ch9-16 fader and master fader to 0.
Output the sound of the sound source to record and adjust
the [TRIM] to an appropriate gain.
The guideline for optimal gain is when the
[PEAK]
LED is
about to light when the sound source is turned up to the
maximum volume.
Accordingly, equalize the signals of ch9-16 being recorded
and/or adjust the PAN according to the sound source.
Refer to the earlier section for instructions on adjusting
the equalizer.
10
11
12
13
Summary of Contents for VF-160
Page 153: ......
