FORTEZA FMC 24 Pro General Description Manual Download Page 35

Page: 35 / 36

FORTEZA JSC FORTEZA FMC 24 Pro (100m, 200m, 300m)

Please visit our internet sites:

www.forteza.com

www.forteza.eu

Page 35

13.7. It is recommended to install a separate switch on the power supply line.

15.

STORAGE

15.1.

The detectors should be stored in the package in warehouses at an ambient

tempe5



С…+30



С and relative humidity 85% maximum.

During storage the influence of hostile environment should be prevented.

16. TRANSPORTATION

16.1

. Packaged detectors can be transported by any transport (if by plane – in

pressurized modules) if they are transported in covered cars, holds or covered bodies they
can be transported at the distance up to 10 000 km.

The boxes should be placed to prevent their shifting or fall in case of jolts and blows.

Summary of Contents for FMC 24 Pro





































Search results

Summary of Contents for FMC 24 Pro

Reviews:

Related manuals for FMC 24 Pro

Brands by name

Popular brands

FORTEZA FMC 24 Pro, General Description Manual

Search results

Summary of Contents for FMC 24 Pro

Reviews:

Related manuals for FMC 24 Pro

Brands by name

Popular brands