FORTEZA FMC 24 Pro General Description Manual Download Page 32 | Manualshive

Page: 32 / 36

background image

FORTEZA JSC FORTEZA FMC 24 Pro (100m, 200m, 300m)

Please visit our internet sites:

www.forteza.com

Page 32

Figure 8.2

9. INSTALLATION OF SOFTWARE FOR COMPUTER USING MICROSOFT

WINDOWS OPERATION SYSTEM.

You can download the latest installation version of the software from our website

http://www.forteza.com

→ support, or you can find it in the USB flash drives, which will

come in delivery set of the senor. Software is names as

Forteza Software Windows

(stylized F with orange-coloured edging).

The first time you run the program, you need to select the communication port (COM-

Port).

Connection to the computer is carried out in two ways:

1. Connect the RS 485/USB program converter using the cable with the plug connector

(included in the delivery set) and connect to the receiver's port RS-485. On the main window
in Communication settings tab→Detector address must be selected for Jack(253)

2. Connect the RS 485 program converter to communicational network wires (RS A to

white, RS B to green), which are in the receiver’s eight-strands wire. On the main window in
Communication settings tab→Detector address must be selected for a number (by factory
default-1).

Converter can be RS-BL or RS485 to USB.

Further work with the software is intuitively clear and analogical to work with

Forteza Android Software.

«
...
30
31
32
33
34
...
»

Summary of Contents for FMC 24 Pro





































Reviews:

No comments

Related manuals for FMC 24 Pro

Brand: G-Tek Pages: 28

Securicam DCS-3415

Brand: D-Link Pages: 3

Brand: D-Link Pages: 20

DCS-6004L? DCS-6005L

Brand: D-Link Pages: 12

Brand: D-Link Pages: 7

Brand: D-Link Pages: 26

DCS-931L Cloud Camera 1050

Brand: D-Link Pages: 40

Brand: D-Link Pages: 45

Brand: WATERGUARD Pages: 2

Brand: MagicRadar Pages: 98

CombiFinder Plus

Brand: LaserLiner Pages: 10

Brand: Neat Pages: 30

Brand: Vaxcel Pages: 5

Brand: Hanwha Vision Pages: 15

Brand: jablotron Pages: 2

Brand: Hitron Pages: 71

INFRAcontrol R 180

Brand: Kopp Pages: 2

Brand: Hitron Pages: 21

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands