Fluke CombiScope PM3370B Reference Manual Download Page 37 | Manualshive

Page: 37 / 133

background image

CHARACTERISTICS

1 - 25

CHARACTERISTICS

SPECIFICATION

ADDITIONAL
INFORMATION

1.9.4

Trace Memory

PM3384B/PM3394B
This digitizer has a total acquisition memory size of 32K bytes. To apply this
memory as efficiently as possible, it is shared by all channels connected to it. The
following section summarizes the effects:

Record length normal
1 to 4 channels selected

512 samples/channel

Record length ’Max’

See Note 1

3 or 4 channels selected

8K samples/channel

2 of 4 channels selected

16K samples/channel

1 of 4 channels selected

32K samples

Display

501 samples/trace

PM3370B/80B/90B:
This digitizer has a total acquisition memory size of 8K bytes. To apply this
memory as efficiently as possible, it is shared by all channels connected to it. The
following section summarizes the effects:

Record length normal
1 and 2 channels selected

512 samples/channel

See Note 2

Record length ’Max’

See Note 1 and 4

2 channels selected

2K samples/channel

See Note 2

2 channels selected

4K samples/channel

See Note 3

1 of 2 channels selected

8K samples

See Note 3

Display

501 samples/trace

Note 1: When peak detection or envelope is activated, all "max" record length

figures have to be divided by 2 because samples are stored as
peak/peak combinations.

Note 2: Trigger view possible.

Note 3: No trigger view possible.

Note 4: When extended memory option is installed total acquisition memory is

32K bytes, shared by both channels and external trigger. This results in
the following max. record lengths:
2 channels and trig.view

8K samples/channel.

2 channels, no trig.view

16K samples/channel.

1 of 2 channels, no trig.view 32K samples/channel.

«
...
35
36
37
38
39
...
»

Summary of Contents for CombiScope PM3370B






































































































































Reviews:

No comments

Related manuals for CombiScope PM3370B

Brand: ABB Pages: 36

Brand: ABB Pages: 40

Brand: Radarcan Pages: 40

Brand: Kawai Pages: 10

Brand: Parker Pages: 39

Brand: IBEX Pages: 4

Brand: Palmako Pages: 83

Brand: Alpina Pages: 24

Brand: Bird-X Pages: 2

Brand: CombiSteel Pages: 60

Brand: Lightolier Pages: 2

Brand: Numark Pages: 11

CareTips Provox FreeHands FlexiVoice

Brand: Atos Medical Pages: 2

Brand: Garmat Pages: 13

Brand: Gama Sonic Pages: 4

Brand: Pixlip Pages: 15

Brand: Sove Pages: 29

Brand: Astrochefs Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands