Fluke CombiScope PM3370B Reference Manual Download Page 103

Page: 103 / 133

4 - 28

PERFORMANCE TEST

4.3.24

Horizontal deflection; MAIN TB deflection coefficients

The deflection coefficients of the main timebase generator (MAIN TB) are verified
by means of a calibration signal.

Test equipment:

Fluke 5500A mode: marker (Alternative: time marker generator TG 501).

Test set-up:

Settings/procedure:

Apply a 50.0 ns time marker signal to input CH1.

Press the AUTOSET key.

Use a 50

Ω

termination. For instruments with switchable 50

Ω

input

impedance it is recommended to make use of this feature (via
VERT MENU key).

Press the TRIGGER menu key.

Select level-pp ’off’ and ’dc’ from the TRIGGER MAIN TB menu.

Press the TB MODE menu key.

Select ’trig’ from the TB MODE menu.

Adjust the TRIGGER LEVEL control for a correctly triggered display.

Verify the deflection coefficients of MAIN TB with MAGNIFY off (

1) and

MAGNIFY on (

10) according to the requirements in the tables. Use the

deflection error facility of the time marker generator.

Note:
-

Error limits must be measured between the 2nd and the 10th graticule line
(there are 11 graticule lines). These are the central 8 divisions.

With MAGNIFY on (

10), the central 10 divisions of the expanded 100

divisions of MAIN TB are measured.

Summary of Contents for CombiScope PM3370B






































































































































Search results

Summary of Contents for CombiScope PM3370B

Reviews:

Related manuals for CombiScope PM3370B

Brands by name

Popular brands

Fluke CombiScope PM3370B, Reference Manual

Search results

Summary of Contents for CombiScope PM3370B

Reviews:

Related manuals for CombiScope PM3370B

Brands by name

Popular brands