Fluke CombiScope PM3370B Reference Manual Download Page 80 | Manualshive

Page: 80 / 133

background image

PERFORMANCE TEST

4 - 5

4.3.2

Power supply

This test checks the proper operation of the power supply at all possible line
voltages.

Test equipment:

Variable voltage transformer (VARIAC)

Test set-up:

Settings/procedure:

1

-

Adjust the input line voltage to the oscilloscope (output from VARIAC) to a
desired value between 100 and 240V (rms), frequency 50...400 Hz.

2

-

Press POWER ON on the oscilloscope.

3

-

Apply the Probe Adjust signal from the front panel of the oscilloscope to
input CH1, e.g., by means of a 10:1 probe.

4

-

Press the green AUTOSET key.

Requirements:

1

-

Verify that the oscilloscope starts at any input voltage between 100 and
240V; in particular the line voltages 100, 120, 220 and 240V must be
checked.

2

-

Verify that the instrument’s performance does not change over the
indicated voltage range; and that the displayed Probe Adjust signal is
distortion-free and has equal intensity.

3

-

Press the ANALOG key (’DIGITAL MODE’ is displayed briefly), and verify
that the instrument’s performance does not change in digital mode at the
indicated line voltages (100, 120, 220 and 240V). The displayed Probe
Adjust signal must be free from distortion.

4

-

Press the ANALOG key (’ANALOG MODE’ is displayed briefly) to switch
to analog mode.

CH1

Probe
Adjust

CH2

CH3

CH4

OSCILLOSCOPE UNDER TEST

VARIAC

OUTPUT

TO MAINS

OSC POWER CORD

PROBE

MAT4127

9303

«
...
78
79
80
81
82
...
»

Summary of Contents for CombiScope PM3370B






































































































































Reviews:

No comments

Related manuals for CombiScope PM3370B

Brand: UNIA Pages: 62

Brand: R2 Pages: 20

Brand: Parr Instrument Pages: 24

Brand: JBL Pages: 15

Brand: Above All Pages: 4

Brand: Qu-Bit Electronix Pages: 15

Brand: TC Electronic Pages: 67

Brand: Tascam Pages: 3

LED Street Bar 16x3W RGB IP65

Brand: Varytec Pages: 9

Brand: VARILITE Pages: 8

EVENTPROFILE VL800

Brand: Vari Lite Pages: 34

Optica 30 Series

Brand: Varex Imaging Pages: 36

Brand: Ultraflex Pages: 52

Brand: Palmgren Pages: 12

Brand: Bartscher Pages: 20

Brand: Rigol Pages: 12

Brand: Petzl Pages: 15

Brand: Exmark Pages: 40

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands