Fluke CombiScope PM3370B Reference Manual Download Page 111

Page: 111 / 133

4 - 36

PERFORMANCE TEST

4.3.31

Horizontal deflection; X deflection coefficient via ’line’

The amplification of the horizontal amplifier via the line trigger signal is checked.
Do this test only when 220V line voltage is available.

Test equipment:

None

Settings/procedure:

Press the AUTOSET key.

Press the DISPLAY menu key.

Press X-DEFL softkey.

Select ’on’ and ’line’ from the X-DEFL menu.

Requirements:

Verify that a horizontal line of 4.3 to 7.7 divisions is displayed when the line
voltage is 220V (rms).

4.3.32

Horizontal deflection; high frequency response

In this test, the bandwidth of the horizontal amplifier is checked.

Test equipment:

Fluke 5500A mode: levsine (Alternative: constant amplitude sine wave generator
SG 503).

Test set-up:

Summary of Contents for CombiScope PM3370B






































































































































Search results

Summary of Contents for CombiScope PM3370B

Reviews:

Related manuals for CombiScope PM3370B

Brands by name

Popular brands

Fluke CombiScope PM3370B, Reference Manual

Search results

Summary of Contents for CombiScope PM3370B

Reviews:

Related manuals for CombiScope PM3370B

Brands by name

Popular brands