Fluke CombiScope PM3370B Reference Manual Download Page 5 | Manualshive

Page: 5 / 133

background image

V

-

Cursor measurements with 1% accuracies.

-

Extensive set of fully automated voltmeter and time measurement functions.

-

Probe operated ’Touch Hold and Measure’ function freezes the display and
instantly displays the signal frequency, amplitude and dc voltage level.

-

Peak detection for the capture of glitches as narrow as 5 ns.

-

Pattern, State and Glitch triggering (2 ns, only in the 4 channel models).

-

Event delay and pretriggering and posttriggering.

-

TV triggering including HDTV and TV line selection.

-

Serial interface for printing and plotting.

-

Averaging to reduce signal noise and to increase the vertical resolution from
8 to 16 bits.

-

Advanced mathematics, including digital low-pass filtering. A Math+ option
adds integration, differentiation, histogramming, and (as part of a option) FFT.

-

Sine interpolation and magnification which enables true to life four channel
single shot acquisitions with a timebase up to 625 ns/div (32x magnified)

-

A delayed timebase with full trigger features.

-

An EIA-232-D interface (standard) and an GPIB/IEEE-488 interface
(optional).

-

Autocal for automatic fine tuning of all circuitry to achieve maximum accuracy
under all user conditions.

-

Closed case calibration for efficient maintenance of traceable calibration at
minimum cost.

The following options are available:

-

A MATH+ option with more automated measurement functions including
envelope and measurement pass/fail testing. Also included in this option are
Integration, Differentiation, Histogramming, and FFT.

-

Memory extension offering 32K acquisition memory and the ability to store
204 traces (of 512 samples each) in memory.

-

IEEE-488.2 interface using the new SCPI (Standard Commands for
Programmable Instruments) industry standard for remote control of test and
measurement equipment.

«
...
3
4
5
6
7
...
»

Summary of Contents for CombiScope PM3370B






































































































































Reviews:

No comments

Related manuals for CombiScope PM3370B

Brand: Nautilus Pages: 17

Brand: National Instruments Pages: 6

Brand: Rane Pages: 6

Brand: Rane Pages: 27

Brand: Ranger Products Pages: 6

Brand: Rane Pages: 88

Brand: Haag-Streit Pages: 21

Brand: Tar River Pages: 44

Brand: Tar River Pages: 61

Brand: Park House Healthcare Pages: 32

So-exercise TX7

Brand: T-SoX Pages: 8

SimNewB Anomaly Set

Brand: laerdal Pages: 10

Brand: Ametek Pages: 20

Brand: VibraPEP Pages: 2

SonicShield I Micro

Brand: CMS Marine Pages: 15

Brand: Dean Pages: 2

Brand: HunterLab Pages: 29

neoBLUE LED Phototherapy Radiometer

Brand: natus Pages: 18

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands