Fluke CombiScope PM3370B Reference Manual Download Page 32

Page: 32 / 133

1 - 20

CHARACTERISTICS

SPECIFICATION

ADDITIONAL
INFORMATION

1.6

PROCESSING

1.6.1

Preprocessing

PREPROCESSING FUNCTIONS

See Note 1

Invert

CH2; CH4

Add

CH1+CH2; CH3+CH4;
See Note 2

Subtract

CH1-CH2; CH3-CH4;
See Note 2

Peak detection

Real time only

Average

See Note 3

Envelope

Note 1: These functions are performed before the acquisition data is stored in

the acquisition registers. PM3370B/80B/90B; offer two channels, CH1
and CH2.

Note 2: Dynamic range in digital mode

5 div.

Note 3: Average factor 2 to 4096 in power of 2 sequence.

1.6.2

Register Processing (Digital Mode)

See Note 1

Add

See Note 2

Sub

See Note 2

Mul

See Note 2

Filter

LF filter with adjustable
-3dB point

Note 1: There may be run two processes simultaneously. The acquisition

registers can also be used as source registers. The result from process
one will be stored in memory one. The result from process two will be
stored in memory two.

Note 2: The source can be any trace from any register except the result register.

The result can be scaled.

Summary of Contents for CombiScope PM3370B






































































































































Search results

Summary of Contents for CombiScope PM3370B

Reviews:

Related manuals for CombiScope PM3370B

Brands by name

Popular brands

Fluke CombiScope PM3370B, Reference Manual

Search results

Summary of Contents for CombiScope PM3370B

Reviews:

Related manuals for CombiScope PM3370B

Brands by name

Popular brands