Fluke 9100 Series Service Manual Download Page 36

Page: 36 / 74

2/Theory of Operation

2-24

SSGATE- on U12 pin 6 provides the qualifying signal to the clock. In

order to have the clock qualified, the following conditions must be met:

o U12 pin 1 must be high. This line insures that a start has been

received, either by the FOR-START- line being low or by the STRP

signal having the programmed edge on the external START line.

o U12 pin 2 must be high. This line ensures that no external STOP

signal of the programmed edge has been received or that vector

driving is not yet complete (DONE- on U13 pin 1 clears the pin 5

output, thereby disabling SSGATE-).

o U12 pin 4 must be high. This is the ENA-RCVD line, and is either

high all the time (if ENA-ALWAYS is high) or high only when the

input on the external ENABLE line is at the programmed level.

o U12 pin 5 must be high. This is the HS-ENABLE line and is high if

vector driving is not suspended awaiting a WAIT input. If a WAIT

statement has been reached in the vector file, the HSOUT line of the

Vector Control RAM is active and sets the HS-ENABLE low, suspending

vector driving. (The following text describes handshake

synchronization in more detail.)

HANDSHAKE SYNCHRONIZATION

The handshake synchronization circuitry allows the Vector Output I/O

Module to suspend vector driving until the desired edge has been

detected on the WAIT input (P1 pin 3) of the Main PCA.

The handshake synchronization circuit consists of a 74ACT74 Dual D-Type

Flip-Flop (U8), a 74AC20 Quad Input NAND Gate (U12), and a 74ACT86

Exclusive OR Gate (U17), all on the Top PCA.

Prior to vector driving, the START-ENA line is set low. This signal is

gated by U12 and U17 and is routed to U8-10, which initializes the

HS-ENABLE line from U8-9 high. HS-ENABLE permits SSGATE- to be low upon

receipt of a start and enable with no stop. START-ENA is returned high

to enable vector driving so that U8-10 is not being held to SET-.

HSIN-POL (U5-15) is set to the proper polarity (high) when the vector

file is loaded.

When a vector is driven and is followed by a vector file WAIT statement,

the HSOUT line (U601-16) goes high. This generates a rising edge on U8

pin 11 that sets U8-9 HS-ENABLE low, which returns SSGATE- high (i.e.,

no clocks are permitted to drive vectors). U8-8 is set high as the data

input to U8-2. Upon the receipt of the proper edge on Pl pin 3 (WAIT) on

the Main PCA, HSIN is passed through U17 to become HSIN-PLUS, providing

a rising edge to U8-3, which clocks U8, setting U8-6 low. This low

signal sets the U12-8 output high. This signal is inverted by U17 and is

applied as a low to the U8-10 SET- input. When pin 10 is set, HS-ENABLE

(U8-9) returns high, which sets SSGATE- low (allowing vectors to be

clocked out). U8-8 is also set low, which removes the SET- low signal

from U8-10. The HS-ENABLE signal also goes through J4-36 on the Top PCA

to J3-36 on the Main PCA to U25-12, where the status can be observed by

bit 2 of the Vector Drive Status Nybble.

Summary of Contents for 9100 Series










































































Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands

Fluke 9100 Series, Service Manual

Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands