Fluke 9100 Series Service Manual Download Page 18

Page: 18 / 74

2/Theory of Operation

2-6

shows the third least significant digit of the 5-digit hex module

address broken down into binary format. The position of the set bit(s)

determines the module(s) to be addressed.

The Vector Output I/O Module bus interface timing diagram (Figure 2-6)

shows the signals contained in the bus interface block during a read and

write cycle. Each transition point (indicated by the letters A through

I) designates the following actions:

A. The address appears on the bus. R/W- goes high, signifying a read

cycle.

B. STROBE- goes low, allowing RD- and CSX- to go active. Data bus

transceiver U8 turns on, driving data from the module to the

mainframe. Addresses and R/W- are latched by U7 and are guaranteed

valid.

C. Valid read data appears on the data bus.

D. STROBE-, RD-, and CSX- return high. Read data is guaranteed valid at

this point.

E. End of the read cycle.

F. The address appears on the bus. R/W- goes low, signifying a write

cycle.

G. STROBE- goes low, allowing WR- and CSX- to go active. Data bus

transceiver U8 turns on, receiving data from the mainframe to the

module. Addresses and R/W- are guaranteed valid.

H. STROBE-, WR-, and CSX- return high. Write data is latched into the

module registers.

I. End of the write cycle.

CUSTOM CHIP SELECTION

The Bus Interface also decodes address lines A1 through A7 from the

mainframe to determine which custom chips are enabled. As the address

signals enter the Main PCA through J1, the address lines are latched by

U7 (the latch signal is STROBE-). Address lines A7 through A4 are used

as address inputs for the decoder (U6). The outputs of U6 are gated to

determine which custom chip is enabled. Any one of the five custom chips

can be addressed, or all five of the chips can be addressed

simultaneously (no other combination of the custom chips can be

addressed within a module).

For example, to select custom chip U100, the input at U7-13 (A7) from

the address bus of the mainframe must be at logic high and U7-18 (A4),

U7-17 (A5), and U7-14 (A6) must be at logic low. When STROBE- occurs, U7

latches the logic levels on these pins. On the output lines of U7,

LAT-A7 is set at logic high, and LAT-A4, LIT-A5, and LAT-A6 are logic

Summary of Contents for 9100 Series










































































Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands

Fluke 9100 Series, Service Manual

Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands