Fluke 9100 Series Service Manual Download Page 3

Page: 3 / 74

-i-

Table of Contents

______________________________________________________________________________

SECTION TITLE PAGE

1 Introduction and Specifications ........................... 1-1

INTRODUCTION1 ............................................ 1-1

SPECIFICATIONS ........................................... 1-1

Theory of Operation ....................................... 2-1

VECTOR OUTPUT I/O MODULE OVERVIEW ........................ 2-1

INPUT SECTION THEORY OF OPERATION ........................ 2-5

Mainframe to Bus Interface Functional Block ......... 2-5

MAINFRAME ADDRESSING OF THE MODULE ............. 2-5

CUSTOM CHIP SELECTION .......................... 2-6

Custom Chip Functional Block ........................ 2-8

Clock and Enable Mux Functional Block ............... 2-9

CLOCK AND ENABLE MUX OPERATION ................. 2-9

General Control Latch Functional Block .............. 2-11

CONTROL REGISTER ............................... 2-12

DATA COMPARISON INPUTS ......................... 2-12

FUSE DETECTION ................................. 2-12

DATA COMPARISON AND GENERAL INTERRUPTS ......... 2-13

DATA COMPARE EQUAL OUTPUT PIN .................. 2-13

OPERATION OF GENERAL CONTROL LATCH BLOCK ....... 2-13

Connector Code Functional Block ..................... 2-16

Input Protection Functional Block ................... 2-16

OUTPUT SECTION THEORY OF OPERATION ....................... 2-16

Main PCA to Top PCA Interface Functional Block ...... 2-17

ADDRESSING ..................................... 2-18

Internal Oscillator Control Functional Block ........ 2-20

Output Control Functional Block ..................... 2-20

RAM Select Functional Block ......................... 2-21

CHIP COUNTER OPERATION ......................... 2-22

SSLOGIC (Start/Stop Logic) Functional Block ......... 2-22

SIGNAL POLARITY/CONTROL REGISTER ............... 2-22

DRIVE CLOCK SELECTION .......................... 2-23

HANDSHAKE SYNCHRONIZATION ...................... 2-24

VECTOR DRIVE COMPLETE LOGIC .................... 2-25

Vector Address Functional Block ..................... 2-26

Vector Pattern RAM Functional Block ................. 2-26

Vector Control RAM Functional Block ................. 2-26

Loop Control Functional Block ....................... 2-27

Capture Clock Functional Block ...................... 2-28

Drive Status Functional Block ....................... 2-28

Output Protection Functional Block .................. 2-29

Summary of Contents for 9100 Series










































































Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands

Fluke 9100 Series, Service Manual

Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands