Fluke 9100 Series Service Manual Download Page 13

Page: 13 / 74

2-1

Section 2

Theory of Operation

VECTOR OUTPUT I/O MODULE OVERVIEW

The 9100A-017 Vector Output I/O Module adds 40 lines of input and

high-speed output capability to the 9100A/9105A mainframe. Up to four

Vector Output I/O Modules may be connected to the mainframe for a

maximum of 160 channels of vector output and stimulus measurement. Any

number of the 160 channels may be used simultaneously.

The Vector Output I/O Module has the same input measurement capabilities

as the 9100A-003 Parallel I/O Module. The Vector Output I/O Module is

capable of generating cyclic redundancy checks (CRCs), measuring

frequency or taking event counts, and recording logic level histories.

The input measurements can be synchronized to the 9100A/9105A

microprocessor-specific Pod, to external events (using the module

external START, STOP, ENABLE, and CLOCK lines), to a software strobe, or

to a free-running clock. The input section may also be synchronized to

the output section by using the Capture Clock (a user-programmable clock

generated during vector driving). The module also has a programmable

“breakpoint” capability. The input thresholds may be set to either “TTL”

and “CMOS” levels.

The Vector Output I/O Module can drive vector patterns synchronized to a

user-supplied external clock (at up to 25 MHz), to a user-selectable

internal clock at 1, 5, 10, or 20 MHz, to a software strobe, or to the

Pod. The output can be latched to a level (either high or low) on any of

the module’s lines to test devices using either a “writeword” or

“writepin” command. Each pin can be driven either high or low, or be

tri-stated. An external input is available to provide handshaking

synchronization with the UUT. All 40 outputs can be simultaneously

tri-stated by an external signal.

The Vector Output I/O Module consists of two assemblies: the Main PCA

(9100A-4021) and the Top PCA (9100A-4022).

The Main PCA provides the interface to the mainframe, and is used for

input measurements. The Main PCA includes the inputs for the external

synchronization lines START, STOP, ENABLE, and CLOCK. It also contains

some support circuitry for vector driving, including:

o bus interfacing circuitry for the Top PCA.

o vector drive internal clock control.

o vector loop control circuitry.

Summary of Contents for 9100 Series










































































Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands

Fluke 9100 Series, Service Manual

Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands