Fluke 9100 Series Service Manual Download Page 37

Page: 37 / 74

2/Theory of Operation

2-25

VECTOR DRIVE COMPLETE LOGIC

There are two different mechanisms for controlling the completion of

vector driving, both of which are selected by the vector file in use.

The Vector Drive Complete circuitry consists of a 74AC02 NOR Gate (U20),

a 74ACT86 Exclusive OR Gate (U17), a 74ACT74 D Flip-flop (U16), and a

74AC08 AND Gate (U19).

Performing a General Stop

To stop the vector at a certain location within the vector file, a STOP

statement may be placed in the vector file. The DONEDRV line (U601-15)

goes high at the final vector address. DONEDRV is inverted by U20, which

produces the DONE- signal. DONE- does not allow the CLKMUX-OUT signal to

pass from U19-2 to U19-3. DONE- also clears U13 (which disables SSGATE-

by setting it high) to prevent further clocking of the RAM. DONE- is

also routed through J5-28 to J4-28 on the Main PCA to U25-16, where the

vector drive status is reflected in bit 3 of the Status Nybble.

Performing a Loop and Stop

To loop a specified number of times and then stop vector driving with no

further vectors being driven, a STOP statement may be placed after an

ENDLOOP statement in the vector file.

The LOOP-DONE signal is normally low. This signal remains low until the

final pass through the loop has begun. As long as LOOP-DONE is low, the

output of U16-9 is also low, preventing the BOTH signal from passing

through U19.

The LOOP signal is active one vector before the end of the loop to

permit address loading (since the module uses a pipeline scheme). The

BOTH signal is active at the same time as the final vector of the loop

is driven. Since U17 inverts BOTH, the current status of LOOP-DONE is

not latched until the first vector in the loop is driven (BOTH returns

low, clocking U16).

At the conclusion of the next-to-last pass through the loop, LOOP-DONE

is set high. On the last vector of the loop, BOTH goes high. When the

first vector of the loop is driven, BOTH returns low. The inversion of

BOTH latches LOOP-DONE, setting U16-9 high. As soon as the last vector

in the last pass through the loop is driven, BOTH returns high and

U19-6 goes high, generating the DONE- signal. From this point, the

signal is routed as described in the heading “Performing a General

Stop.”

See the Loop Control Function Block for further information on how

looping operates.

Summary of Contents for 9100 Series










































































Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands

Fluke 9100 Series, Service Manual

Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands