Fluke 9100 Series Service Manual Download Page 24

Page: 24 / 74

2/Theory of Operation

2-12

Table 2-2. Clock and Enable Mux Truth Table

________________________________________________________

Control In Outputs

________________________________________________________

CLKMUX ENAMUX XEN XCK

________________________________________________________

0 0 BUFENABLE BUFCLOCK

0 1 PSYN BUFCLOCK

1 0 BUFENABLE CAPTURE-

1 1 PSYN CALCLK2

________________________________________________________

block diagram. The ICs in this block include: a 74HC273 8-Bit Latch

(U14), an LM324 Quad Op-Amp (U2), two 2N3906 PNP transistors (Ql, Q2), a

74HC08 Quad 2-Input AND Gate (U3), a 74LS30 8-Input NAND Gate (U15), two

74LS112 Dual JK Negative-Edge-Triggered Flip-Flops (U11, U12), a 74HCT32

Quad 2-Input OR Gate (U10), and a 74HCT244 Octal Buffer (U13).

CONTROL REGISTER

Data lines from the A-D-BUS to U14 produce the DCECLR- (Data Compare

Equal Clear), GENCLR- (General Clear), FUSECLR- (Fuse Clear), ENMUX

(Enable Multiplex), CLKMUX (Clock Multiplex), and THRSH (Threshold)

signals. U14 is accessed by a write to $DXXDX, where the ADD- and WR-

signals latch data into U14. The Control Register (U14) is cleared by a

PWRUP (Power Up) signal held low by C44 to ensure a proper reset. See

Figure 2-7 for the Control Register bit position.

The J2 and J3 connectors provide the input to the General Control Latch

block for detection of Clip and Calibration Modules. J2-25 and J3-25 are

the input pins to a detection circuit that provides SWLDET (the

left-hand or A Switch Detect) and SWRDET (the right-hand or B Switch

Detect) signals to generate an interrupt. The mainframe reads the

interrupt register (U13) to determine the reason for an interrupt. See

Figure 2-7 for the interrupt register bit positions.

DATA COMPARISON INPUTS

All 40 lines of the module are compared to programmable data registers

and are qualified by programmable “don’t care” registers. The comparison

is done inside the custom chip(s) between the data on the input lines

and the registers, eight lines per chip. The EQ outputs (pin 55 of the

custom chip) are gated together by U15, and, when they are all high

(i.e., a comparison for all five chips has been detected), an interrupt

is generated and is input to the interrupt register (U13).

FUSE DETECTION

The FUSEDET (Fuse Detect) signal is part of the Multi-Detection area of

the General Control Latch Block. A 1A slow-blow ground fuse located on

Summary of Contents for 9100 Series










































































Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands

Fluke 9100 Series, Service Manual

Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands