Fluke 9100 Series Service Manual Download

Page: 11 / 74

1/Introduction and Specifications

1-3

Table 1-1. Vector Output I/O Module Specifications (cont.)

______________________________________________________________________________

DR CLK

START Setup Time .................. 20 ns minimum.

STOP Setup Time ................... 20 ns minimum.

ENABLE Setup Time ................. 15 ns minimum.

ENABLE Hold Time .................. 35 ns minimum.

Input Impedance:

DR CLK ................................. 40 kilohm minimum, 35 pF maximum.

TRISTATE- .............................. 40 kilohm minimum, 80 pF maximum.

WAIT ................................... 40 kilohm minimum, 50 pF maximum.

VECTOR OUTPUT I/O MODULE INPUT:

Input Impedance ............................ 50 kilohm minimum, 90 kilohm

typical; 100 pF maximum, 65 pF

typical.*

Operating Voltage Range .................... -0.5V to +5.5V (all lines).

Input/Output Protection .................... +10V/-5V for one minute

maximum, one line only (all

lines).

Input Thresholds:

________________________________________________

| | | |

| TTL | CMOS | |

|_________|__________|___________________________|

| | | |

| 5.0V | 5.0V | \ |

| | | >- Guaranteed HIGH |

| 2.6V | 3.4V | < |

| | | >- HIGH or INVALID |

| 2.1V | 2.9V | < |

| | | >- Guaranteed INVALID |

| 1.0V | 1.2V | < |

| | | >- LOW or INVALID |

| 0.6V | 0.8V | < |

| | | >- Guaranteed LOW |

| 0.0V | 0.0V | / |

|_________|__________|___________________________|

CLOCK, START, STOP, and ENABLE Inputs:

Thresholds:

Logic LOW ......................... 0.8V maximum.

Logic HIGH ........................ 2.0V minimum.

Input Current .......................... 125 uA maximum.

Input/Output Protection ................ +10V/-5V for one minute

maximum, one line only.

______________________________________________________________________________

Input capacitance includes the Y9100A-102 Card Edge Interface Module.

______________________________________________________________________________

Summary of Contents for 9100 Series










































































Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands

Fluke 9100 Series, Service Manual

Search results

Summary of Contents for 9100 Series

Reviews:

Related manuals for 9100 Series

Brands by name

Popular brands