background image

2-wire Intercom System

2 EASY

1

2

3

6

5

4

7

8

9

#

0

*

RF CARD

CONTENTS

INTRODUCTION...........................................................................2

   Installation Guide........................................................................2

CONFIGURATIONS......................................................................4

   Debug State...............................................................................4

   Work Mode.................................................................................8

   Software Update........................................................................10

   Tone Update..............................................................................10

   UI Update...................................................................................11

   Namelist Update.........................................................................12

      by SD Card..............................................................................12

      by DT-Config............................................................................13

DMR18S TECHNICAL MANUAL

Summary of Contents for 2Easy DMR18s
















Reviews: